EP4SE530H40I3 Altera, EP4SE530H40I3 Datasheet - Page 983

• Manufacturer Part Number: EP4SE530H40I3
• Description: IC STRATIX IV FPGA 530K 1517HBGA
• Manufacturer: Altera
• Series: STRATIX® IV Er

Specifications of EP4SE530H40I3

• Number Of Logic Elements/cells: 531200
• Number Of Labs/clbs: 21248
• Total Ram Bits: 27376
• Number Of I /o: 976
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 1517-HBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -

Chapter 1: ALTGX Transceiver Setup Guide for Stratix IV Devices
Parameter Settings
Table 1–6. MegaWizard Plug-In Manager Options (TX Analog Screen) (Part 1 of 2)
February 2011 Altera Corporation
What is the transmitter buffer
power (V
What is the transmitter
common mode voltage (V
Use external transmitter
termination.
Select the transmitter
termination resistance.
What is the voltage output
differential (V
setting?
What is the pre-emphasis first
post-tap setting (% of V
ALTGX Setting
CCH
)?
OD
) control
Table 1–6
Plug-In Manager for your ALTGX custom megafunction variation.
OD
CM
)?
)?
The options available for selection are based on
what you enter in the What is the effective data
rate? option.
■
■
■
It is up to you to connect the correct voltage
supply to the V
The transmitter common mode voltage is fixed to
0.65 V.
This option is available if you want to use an
external termination resistor instead of the
differential OCT. Checking this option turns off the
transmitter differential OCT.
This option selects the transmitter differential
termination value. The settings allowed are 85 Ω,
100 Ω, 120 Ω, and 150 Ω.
This option selects the V
buffer. The available V
on the transmitter termination resistance value.
This option sets the amount of pre-emphasis on
the transmitter buffer using first post-tap.
lists the available options on the TX Analog screen of the MegaWizard
1.4 V—Available up to 8.5 Gbps.
1.5 V is available up to 6.5 Gbps (not available
for Stratix IV GT).
AUTO—The ALTGX MegaWizard Plug-In
Manager automatically sets V
the effective data rates less than 6.5 Gbps
or
V
than 6.5 Gbps.
CCH
to 1.4 V for effective data rates greater
CCH
pins on the board.
Description
OD
OD
settings change based
of the transmitter
CCH
to 1.5 V for
“Programmable Transmit Output
Buffer Power (V
Transceiver Architecture in Stratix IV
Devices
“Transmitter Output Buffer” in the
Transceiver Architecture in Stratix IV
Devices
Switching Characteristics for Stratix IV
Devices
“Programmable Transmitter
Termination” section in the
Architecture in Stratix IV Devices
chapter and the
Characteristics for Stratix IV Devices
section.
“Programmable Transmitter
Termination” section in the
Architecture in Stratix IV Devices
chapter and the
Characteristics for Stratix IV Devices
section.
“Programmable Output Differential
Voltage” section in the
Architecture in Stratix IV Devices
chapter and the
Characteristics for Stratix IV Devices
section.
“Programmable Pre-Emphasis”
section in the
in Stratix IV Devices
Stratix IV Device Handbook Volume 3
chapter.
chapter and the
section.
Reference
Transceiver Architecture
CCH
DC and Switching
DC and Switching
DC and Switching
)” section in the
chapter.
Transceiver
DC and
Transceiver
Transceiver
1–25