D12674RVFQ33D Renesas Electronics America, D12674RVFQ33D Datasheet - Page 788

• Manufacturer Part Number: D12674RVFQ33D
• Description: MCU 3V 0K I-TEMP 144-QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2600r

Specifications of D12674RVFQ33D

• Core Processor: H8S/2600
• Core Size: 16-Bit
• Speed: 33MHz
• Connectivity: IrDA, SCI
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 103
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 12x10b; D/A 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Other names: HD6412674RVFQ33D; HD6412674RVFQ33D

Section 15 Serial Communication Interface (SCI, IrDA)
15.10.3 Mark State and Break Sending
When TE is 0, the TxD pin is used as an I/O port whose direction (input or output) and level are
determined by DR and DDR. This can be used to set the TxD pin to mark state or send a break
during serial data transmission. To maintain the communication line at mark state until TE is set to
1, set both PCR and PDR to 1. Since TE is cleared to 0 at this point, the TxD pin becomes an I/O
port, and 1 is output from the TxD pin. To send a break during serial transmission, first set PCR to
1 and clear PDR to 0, and then clear TE to 0. When TE is cleared to 0, the transmitter is initialized
regardless of the current transmission state, the TxD pin becomes an I/O port, and 0 is output from
the TxD pin.
15.10.4 Receive Error Flags and Transmit Operations (Clocked Synchronous Mode Only)
Transmission cannot be started when a receive error flag (ORER, PER, or FER) is set to 1, even if
the TDRE flag is cleared to 0. Be sure to clear the receive error flags to 0 before starting
transmission. Note also that receive error flags cannot be cleared to 0 even if the RE bit is cleared
to 0.
15.10.5 Relation between Writes to TDR and the TDRE Flag
The TDRE flag in SSR is a status flag that indicates that transmit data has been transferred from
TDR to TSR. When the SCI transfers data from TDR to TSR, the TDRE flag is set to 1.
Data can be written to TDR regardless of the state of the TDRE flag. However, if new data is
written to TDR when the TDRE flag is cleared to 0, the data stored in TDR will be lost since it has
not yet been transferred to TSR. It is therefore essential to check that the TDRE flag is set to 1
before writing transmit data to TDR.
15.10.6 Restrictions on Use of DMAC or DTC
Rev. 3.00 Mar 17, 2006 page 736 of 926
REJ09B0283-0300
When an external clock source is used as the serial clock, the transmit clock should not be
input until at least 5 clock cycles after TDR is updated by the DMAC or DTC. Misoperation
may occur if the transmit clock is input within 4 clocks after TDR is updated. (Figure 15.35)
When RDR is read by the DMAC or DTC, be sure to set the activation source to the relevant
SCI receive-data-full interrupt (RXI).