EP4SE530H35C2N Altera, EP4SE530H35C2N Datasheet - Page 195
EP4SE530H35C2N
Manufacturer Part Number
EP4SE530H35C2N
Description
IC STRATIX IV FPGA 530K 1152HBGA
Manufacturer
Altera
Series
STRATIX® IV Er
Datasheets
1.EP4SGX110DF29C3N.pdf
(80 pages)
2.EP4SGX110DF29C3N.pdf
(1154 pages)
3.EP4SGX110DF29C3N.pdf
(432 pages)
4.EP4SGX110DF29C3N.pdf
(22 pages)
5.EP4SGX110DF29C3N.pdf
(72 pages)
6.EP4SE230F29C3N.pdf
(12 pages)
Specifications of EP4SE530H35C2N
Number Of Logic Elements/cells
531200
Number Of Labs/clbs
21248
Total Ram Bits
27376
Number Of I /o
744
Voltage - Supply
0.87 V ~ 0.93 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
1152-HBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Gates
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP4SE530H35C2N
Manufacturer:
ALTERA
Quantity:
147
- EP4SGX110DF29C3N PDF datasheet
- EP4SGX110DF29C3N PDF datasheet #2
- EP4SGX110DF29C3N PDF datasheet #3
- EP4SGX110DF29C3N PDF datasheet #4
- EP4SGX110DF29C3N PDF datasheet #5
- EP4SE230F29C3N PDF datasheet #6
- Current page: 195 of 1154
- Download datasheet (32Mb)
Chapter 6: I/O Features in Stratix IV Devices
I/O Structure
February 2011 Altera Corporation
Programmable Pull-Up Resistor
Programmable Pre-Emphasis
Programmable Differential Output Voltage
MultiVolt I/O Interface
f
f
f
1
For more information about the specific sustaining current driven through this
resistor and the overdrive current used to identify the next-driven input level, refer to
the
Bus-hold circuitry is active only after configuration. When going into user mode, the
bus-hold circuit captures the value on the pin present at the end of configuration.
Each Stratix IV device I/O pin provides an optional programmable pull-up resistor
during user mode. If you enable this feature for an I/O pin, the pull-up resistor
(typically 25 K ) weakly holds the I/O to the V
Programmable pull-up resistors are only supported on user I/O pins and are not
supported on dedicated configuration pins, JTAG pins, or dedicated clock pins. If you
enable the programmable pull-up option, you cannot use the bus-hold feature.
When the optional DEV_OE signal drives low, all the I/O pins remain tri-stated even
with the programmable pull-up option enabled.
Stratix IV LVDS transmitters support programmable pre-emphasis to compensate for
the frequency dependent attenuation of the transmission line. The Quartus II software
allows four settings for programmable pre-emphasis.
For more information about programmable pre-emphasis, refer to the
Differential I/O Interfaces and DPA in Stratix IV Devices
Stratix IV LVDS transmitters support programmable V
settings allow you to adjust output eye height to optimize trace length and power
consumption. A higher V
smaller V
settings for programmable V
For more information about programmable V
Interfaces and DPA in Stratix IV Devices
The Stratix IV architecture supports the MultiVolt I/O interface feature that allows the
Stratix IV devices in all packages to interface with systems of different supply
voltages.
You can connect the VCCIO pins to a 1.2-, 1.5-, 1.8-, 2.5-, or 3.0-V power supply,
depending on the output requirements. The output levels are compatible with
systems of the same voltage as the power supply. (For example, when VCCIO pins are
connected to a 1.5-V power supply, the output levels are compatible with 1.5-V
systems.)
DC and Switching Characteristics for Stratix IV Devices
OD
swing reduces power consumption. The Quartus II software allows four
OD
swing improves voltage margins at the receiver end; a
OD
.
chapter.
OD
CCIO
, refer to the
level.
chapter.
OD
chapter.
. The programmable V
Stratix IV Device Handbook Volume 1
High-Speed Differential I/O
High-Speed
OD
6–23
Related parts for EP4SE530H35C2N
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
CYCLONE II STARTER KIT EP2C20N
Manufacturer:
Altera
Datasheet:
Part Number:
Description:
CPLD, EP610 Family, ECMOS Process, 300 Gates, 16 Macro Cells, 16 Reg., 16 User I/Os, 5V Supply, 35 Speed Grade, 24DIP
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
CPLD, EP610 Family, ECMOS Process, 300 Gates, 16 Macro Cells, 16 Reg., 16 User I/Os, 5V Supply, 15 Speed Grade, 24DIP
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
CPLD, EP610 Family, ECMOS Process, 300 Gates, 16 Macro Cells, 16 Reg., 16 User I/Os, 5V Supply, 30 Speed Grade, 24DIP
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
High-performance, low-power erasable programmable logic devices with 8 macrocells, 10ns
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
High-performance, low-power erasable programmable logic devices with 8 macrocells, 7ns
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
Classic EPLD
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
High-performance, low-power erasable programmable logic devices with 8 macrocells, 10ns
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
CPLD, EP610 Family, ECMOS Process, 300 Gates, 16 Macro Cells, 16 Reg., 16 User I/Os, 5V Supply, 25 Speed Grade, 24DIP
Manufacturer:
Altera Corporation
Datasheet: