PNX1702EH/G,557 NXP Semiconductors, PNX1702EH/G,557 Datasheet - Page 779

• Manufacturer Part Number: PNX1702EH/G,557
• Description: IC MEDIA PROC 500MHZ 456-BGA
• Manufacturer: NXP Semiconductors

Specifications of PNX1702EH/G,557

• Applications: Multimedia
• Core Processor: TriMedia
• Controller Series: Nexperia
• Ram Size: 208K x 8
• Interface: I²C, 2-Wire Serial
• Number Of I /o: 61
• Voltage - Supply: 1.33 V ~ 1.47 V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 456-HBGA
• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Program Memory Type: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 935281647557; PNX1702EH/G; PNX1702EH/G

Philips Semiconductors
Volume 1 of 1
Table 7: IIC Registers
PNX17XX_SER_1
Preliminary data sheet
Bit
Offset 0x04 5FE0
31:1
0
Offset 0x04 5FE4
31:1
0
Offset 0x04 5FE8
31:1
0
Note: The IIC module will look at a new transaction on the I
Therefore, software must make sure that “interrupt clear” is the last transaction that is sent to the IIC module before starting
a new transaction.
Offset 0x04 5FEC
31:1
0
Offset 0x04 5FF0
Offset 0x04 5FF4
31
30:0
Offset 0x04 5FF8
Offset 0x04 5FFC
31:16
15:12
11:8
7:0
Acces
s
R
R/W
W
W
R/W
R
R
R
R
Value
-
0
-
0
-
0
-
0
0
-
0x0105
0x0
0x3
0x00
…Continued
I2C INTERRUPT STATUS REGISTER
I2C INTERRUPT ENABLE REGISTER
I2C INTERRUPT CLEAR REGISTER
I2C INTERRUPT SET REGISTER
Reserved
I2C POWERDOWN REGISTER
Reserved
I2C MODULE ID REGISTER
Symbol
Unused
INT_STATUS
Unused
INT_ENABLE
Unused
INT_CLEAR
Unused
INT_SET
POWER_DOWN
Unused
MODULE ID
MAJREV
MINREV
MODULE APERTURE
SIZE
Rev. 1 — 17 March 2006
Description
Ignore upon read. Write as zeroes.
Interrupt status register. It reports any pending interrupts:
Ignore upon read. Write as zeroes.
Interrupt enable register
Ignore upon read. Write as zeroes.
Interrupt clear register.
Ignore upon read. Write as zeroes.
Interrupt set register. Allows software to set interrupts.
Module returns DEADABBA on all reads except for reads of the
powerdown bit. Module generates ERR ACK on all writes except for
writes to the powerdown bit.
Ignore upon read. Write as zeroes.
Unique 16-bit code. Module ID
Major Revision
Minor Revision
Aperture size = 4 kB*(bit_value+1), so 0 means 4 kB (the default).
1 = Interrupt i pending.
0 = Interrupt i not pending.
1 = Interrupt i is enabled.
0 = Interrupt is disabled.
1 = Interrupt is cleared.
0 = Interrupt is not cleared.
1 = Interrupt is set
0 = Interrupt is not set.
0 = Normal operation of peripheral. This is the reset value.
1 = Module is powerdown and module clock can be removed.
2
C bus as soon as the previous interrupt has been cleared.
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
PNX17xx Series
Chapter 25: I
2
C Interface
25-18