SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 1137

• Manufacturer Part Number: SAM3U2C
• Manufacturer: Atmel Corporation

Specifications of SAM3U2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

43.9.3.1
43.9.3.2
Table 43-46. SPI Timings
6430E–ATARM–29-Aug-11
Symbol
SPI
Master Write Mode
Master Read Mode
Slave Read Mode
Slave Write Mode
0
Maximum SPI Frequency
SPI Timings
Parameter
MISO Setup time before SPCK rises (master)
Figure 43-15. SPI Slave Mode with (CPOL = NCPHA = 0) or (CPOL= NCPHA= 1)
The following formulas give maximum SPI frequency in Master read and write modes and in
Slave read and write modes.
NPCS0
MISO
MOSI
SCK
The SPI is only sending data to a slave device such as an LCD, for example. The limit is
given by SPI
speed (see
pad.
T
DataFlash (AT45DB642D), T
In the formula above, F
In slave mode, SPCK is the input clock for the SPI. The max SPCK frequency is given by
setup and hold timings SPI
the pad limit, the limit in slave read mode is given by SPCK pad.
For 3.3V I/O domain and SPI6, F
before sampling data.
f
f
SPCK
SPCK
valid
is the slave time response to output data after detecting an SPCK edge. For Atmel SPI
Max
Max
=
=
Section 43.9.2 “I/O
2
SPI
--------------------------------------------------------
SPI
-------------------------------------------------------- -
SPI
(or SPI
15
0
6
(
(
orSPI
orSPI
5
) timing. Since it gives a maximum frequency above the maximum pad
SPCK
1
1
3
9
)
)
SPI
Max = 38.5 MHz @ VDDIO = 3.3V.
7
+
+
3.3V domain
1.8V domain
/SPI
valid
Conditions
T
T
9
valid
setup
Characteristics”), the max SPI frequency is the one from the
(orT
8
SPCK
(or SPI
SPI
v
Max = 33 MHz. T
10
) is 12 ns Max.
(1)
(2)
10
/SPI
11
SPI
). Since this gives a frequency well above
11
Min
14
17
setup
is the setup time from the master
SAM3U Series
Max
SPI
Units
14
ns
ns
1137