SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 987

• Manufacturer Part Number: SAM3U2C
• Manufacturer: Atmel Corporation

Specifications of SAM3U2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

• WAKE_UP: Wake Up CPU Interrupt
0 = cleared by setting the WAKE_UP bit in UDPHS_CLRINT.
1 = set by hardware when the UDPHS controller is in SUSPEND state and is re-activated by a filtered non-idle signal from
the UDPHS line (not by an upstream resume). This triggers a UDPHS interrupt when the WAKE_UP bit is set in
UDPHS_IEN register. When receiving this interrupt, the user has to enable the device controller clock prior to operation.
Note:
• ENDOFRSM: End Of Resume Interrupt
0 = cleared by setting the ENDOFRSM bit in UDPHS_CLRINT.
1 = set by hardware when the UDPHS controller detects a good end of resume signal initiated by the host. This triggers a
UDPHS interrupt when the ENDOFRSM bit is set in UDPHS_IEN.
• UPSTR_RES: Upstream Resume Interrupt
0 = cleared by setting the UPSTR_RES bit in UDPHS_CLRINT.
1 = set by hardware when the UDPHS controller is sending a resume signal called “upstream resume”. This triggers a
UDPHS interrupt when the UPSTR_RES bit is set in UDPHS_IEN.
• EPT_x: Endpoint x Interrupt
0 = reset when the UDPHS_EPTSTAx interrupt source is cleared.
1 = set by hardware when an interrupt is triggered by the UDPHS_EPTSTAx register and this endpoint interrupt is enabled
by the EPT_x bit in UDPHS_IEN.
• DMA_x: DMA Channel x Interrupt
0 = reset when the UDPHS_DMASTATUSx interrupt source is cleared.
1 = set by hardware when an interrupt is triggered by the DMA Channelx and this endpoint interrupt is enabled by the
DMA_x bit in UDPHS_IEN.
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
this interrupt is generated even if the device controller clock is disabled.
SAM3U Series
SAM3U Series
987
987