SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 346

• Manufacturer Part Number: SAM3U2C
• Manufacturer: Atmel Corporation

Specifications of SAM3U2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

24.6.2
Name:
Address:
Access:
This register can only be written if the WPEN bit is cleared in the
• SLOT_CYCLE: Maximum Number of Allowed Cycles for a Burst
When the SLOT_CYCLE limit is reach for a burst it may be broken by another master trying to access this slave.
This limit has been placed to avoid locking very slow slave by when very long burst are used.
This limit should not be very small though. Unreasonable small value will break every burst and Bus Matrix will spend its
time to arbitrate without performing any data transfer. 16 cycles is a reasonable value for SLOT_CYCLE.
• DEFMSTR_TYPE: Default Master Type
0: No Default Master
At the end of current slave access, if no other master request is pending, the slave is disconnected from all masters.
This results in having a one cycle latency for the first acccess of a burst transfer or for a single access.
1: Last Default Master
At the end of current slave access, if no other master request is pending, the slave stay connected with the last master hav-
ing accessed it.
This results in not having the one cycle latency when the last master re-tries access on the slave again.
2: Fixed Default Master
At the end of the current slave access, if no other master request is pending, the slave connects to the fixed master which
number has been written in the FIXED_DEFMSTR field.
This results in not having the one cycle latency when the fixed master re-tries access on the slave again.
• FIXED_DEFMSTR: Fixed Default Master
This is the number of the Default Master for this slave. Only used if DEFMSTR_TYPE is 2. Specifying the number of a mas-
ter which is not connected to the selected slave is equivalent to setting DEFMSTR_TYPE to 0.
6430E–ATARM–29-Aug-11
31
23
15
–
–
–
7
Bus Matrix Slave Configuration Registers
MATRIX_SCFG0..MATRIX_SCFG9
0x400E0240
Read-write
30
22
14
–
–
–
6
29
21
13
–
–
–
5
28
20
12
–
–
4
SLOT_CYCLE
FIXED_DEFMSTR
“Write Protect Mode
27
19
11
–
–
3
26
18
10
–
–
2
Register”.
SAM3U Series
25
17
9
–
1
DEFMSTR_TYPE
ARBT
24
16
8
–
0
346