SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 520

• Manufacturer Part Number: SAM3U2C
• Manufacturer: Atmel Corporation

Specifications of SAM3U2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

30.6
520
520
I/O Lines Programming Example
SAM3U Series
SAM3U Series
The programing example as shown in
configuration.
Table 30-1.
• 4-bit output port on I/O lines 0 to 3, (should be written in a single write operation), open-drain,
• Four output signals on I/O lines 4 to 7 (to drive LEDs for example), driven high and low, no
• Four input signals on I/O lines 8 to 11 (to read push-button states for example), with pull-up
• Four input signals on I/O line 12 to 15 to read an external device status (polled, thus no input
• I/O lines 16 to 19 assigned to peripheral A functions with pull-up resistor
• I/O lines 20 to 23 assigned to peripheral B functions, no pull-up resistor
• I/O line 24 to 27 assigned to peripheral A with Input Change Interrupt and pull-up resistor
with pull-up resistor
pull-up resistor
resistors, glitch filters and input change interrupts
change interrupt), no pull-up resistor, no glitch filter
PIO_OWDR
PIO_MDDR
PIO_OWER
PIO_SODR
PIO_CODR
PIO_MDER
PIO_PUDR
PIO_PUER
PIO_ABSR
PIO_IFDR
PIO_OER
PIO_ODR
PIO_IFER
PIO_PER
PIO_PDR
Register
PIO_IER
PIO_IDR
Programming Example
Table 30-1
Value to be Written
below is used to obtain the following
0xFFFF F0FF
0x0FFF FFFF
0xFFFF FF00
0xF0FF F0FF
0xFFFF FFF0
0x0F0F FF0F
0x0FFF FFF0
0x0000 FFFF
0xFFFF 0000
0xF0F0 00F0
0x0000 00FF
0x0000 0F00
0x0000 0000
0x0F00 0F00
0x0000 000F
0x00F0 0000
0x0000 000F
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11