SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 432

• Manufacturer Part Number: SAM3U2C
• Manufacturer: Atmel Corporation

Specifications of SAM3U2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.18.20 SMC Timings Register
Name:
Address:
Access:
Reset:
• TCLR: CLE to REN Low Delay
Command Latch Enable falling edge to Read Enable falling edge timing.
Latch Enable Falling to Read Enable Falling = (TCLR[3] * 64) + TCLR[2:0] clock cycles.
• TADL: ALE to Data Start
Last address latch cycle to the first rising edge of WEN for data input.
Last address latch to first rising edge of WEN = (TADL[3] * 64) + TADL[2:0] clock cycles.
• TAR: ALE to REN Low Delay
Address Latch Enable falling edge to Read Enable falling edge timing.
Address Latch Enable to Read Enable = (TAR[3] * 64) + TAR[2:0] clock cycles.
• OCMS: Off Chip Memory Scrambling Enable
When set to one, the memory scrambling is activated.
• TRR: Ready to REN Low Delay
Ready/Busy signal to Read Enable falling edge timing.
Read to REN = (TRR[3] * 64) + TRR[2:0] clock cycles.
• TWB: WEN High to REN to Busy
Write Enable rising edge to Ready/Busy falling edge timing.
Write Enable to Read/Busy = (TWB[3] * 64) + TWB[2:0] clock cycles.
• RBNSEL: Ready/Busy Line Selection
This field indicates the selected Ready/Busy Line from the RBN bundle.
• NFSEL: NAND Flash Selection
If this bit is set to one, the chip select is assigned to NAND Flash write enable and read enable lines drive the Error Correct-
ing Code module.
432
432
NFSEL
31
23
15
–
–
7
SAM3U Series
SAM3U Series
0x400E007C [0], 0x400E0090 [1], 0x400E00A4 [2], 0x400E00B8 [3]
SMC_TIMINGSx [x=0..3]
Read-write
0x00000000
30
22
14
–
–
6
TADL
RBNSEL
29
21
13
–
–
5
OCMS
28
20
12
–
4
27
19
11
3
26
18
10
2
TCLR
TWB
TRR
TAR
25
17
9
1
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
24
16
8
0