SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 298

• Manufacturer Part Number: SAM3U2C
• Manufacturer: Atmel Corporation

Specifications of SAM3U2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.5.5
Name:
Address:
Access:
• BODRSTEN: Brownout Detector Reset Enable
0 (NOT_ENABLE) = the core reset signal “vddcore_nreset” is not affected when a brownout detection occurs.
1 (ENABLE) = the core reset signal, vddcore_nreset is asserted when a brownout detection occurs.
• BODDIS: Brownout Detector Disable
0 (ENABLE) = the core brownout detector is enabled.
1 (DISABLE) = the core brownout detector is disabled.
• VDDIORDY: VDDIO Ready
0 (VDDIO_REMOVED) = VDDIO is removed (used before going to backup mode when backup batteries are used)
1 (VDDIO_PRESENT) = VDDIO is present (used before going to backup mode when backup batteries are used)
If the backup batteries are not used, VDDIORDY must be kept set to 1.
• ONREG: Voltage Regulator enable
0 (ONREG_UNUSED) = Voltage Regulator is not used
1 (ONREG_USED) = Voltage Regulator is used
• OSCBYPASS: Oscillator Bypass
0 (NO_EFFECT) = no effect. Clock selection depends on XTALSEL value.
1 (BYPASS) = the 32-KHz XTAL oscillator is selected and is put in bypass mode.
• KEY: Password Key
Should be written to value 0xA5. Writing any other value in this field aborts the write operation.
298
298
31
23
15
–
–
7
–
SAM3U Series
SAM3U Series
Supply Controller Mode Register
SUPC_MR
0x400E1218
Read-write
VDDIORDY
ONREG
30
22
14
–
6
–
BODDIS
29
21
13
–
5
–
OSCBYPASS
BODRSTEN
28
20
12
4
–
KEY
27
19
11
–
–
3
–
26
18
10
–
–
2
–
25
17
–
9
–
1
–
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
24
16
–
8
–
0
–