LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 178

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
3. Pin function select register values
4. Pin mode select register values
5. Register description
UM10237_4
User manual
The PINSEL registers control the functions of device pins as shown below. Pairs of bits in
these registers correspond to specific device pins.
Table 127. Pin function select register bits
The direction control bit in the GPIO registers is effective only when the GPIO function is
selected for a pin. For other functions, direction is controlled automatically. Each
derivative typically has a different pinout and therefore a different set of functions possible
for each pin. Details for a specific derivative may be found in the appropriate data sheet.
The PINMODE registers control the on-chip pull-up/pull-down resistor feature for all GPIO
ports. Two bits are used to control a port pin. PINMODEn register bits are reserved for not
available pins, e.g. pins P2[15:14] are not available on LPC2458 and are reserved in
PINSEL5 and PINMODE5.
Table 128. Pin Mode Select register bits
The Pin Control Module contains 12 registers as shown in
Remark: The LCD pins in the PINSEL registers are available on the LPC247x only.
Table 129. Summary of pin connect block registers
PINSEL0 to
PINSEL9 Values
00
01
10
11
PINMODE0 to
PINMODE9
Values
00
01
10
11
Name
PINSEL0
PINSEL1
PINSEL2
PINSEL3
PINSEL4
PINSEL5
Pin function select register 0
Pin function select register 1
Pin function select register 2
Pin function select register 3
Pin function select register 4
Pin function select register 5
Description
Function
Primary (default) function, typically GPIO port
First alternate function
Second alternate function
Third alternate function
Function
Pin has an on-chip pull-up resistor enabled.
Reserved. This value should not be used.
Pin has neither pull-up nor pull-down resistor enabled.
Pin has an on-chip pull-down resistor enabled.
Rev. 04 — 26 August 2009
Access Reset Value
R/W
R/W
R/W
R/W
R/W
R/W
Chapter 9: LPC24XX Pin connect
0x0000 0000
0x0000 0000
0x0000 0000
0x0000 0000
0x0000 0000
0x0000 0000
Table 9–129
[1]
UM10237
© NXP B.V. 2009. All rights reserved.
Value after Reset
00
Value after Reset
00
below.
Address
0xE002 C000
0xE002 C004
0xE002 C008
0xE002 C00C
0xE002 C010
0xE002 C014
178 of 792