LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 281

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

1. How to read this chapter
2. Basic configuration
3. Introduction
4. Features
UM10237_4
User manual
The LCD controller is available on parts LPC2470 and LPC2478 only.
The LCD controller is configured using the following registers:
The LCD controller provides all of the necessary control signals to interface directly to a
variety of color and monochrome LCD panels.
1. Power: In the PCONP register
2. Clock: see
3. Pins: Enable the LCD controller port using the PINSEL11 register
4. Configuration: see
•
•
•
•
•
•
•
•
•
•
•
•
•
•
UM10237
Chapter 12: LPC24XX LCD controller
Rev. 04 — 26 August 2009
Remark: The LCD is disabled on reset (PCLCD = 0).
Also see
select individual LCD pins using PINSEL0
PINSEL4
AHB bus master interface to access frame buffer.
Setup and control via a separate AHB slave interface.
Dual 16-deep programmable 64-bit wide FIFOs for buffering incoming display data.
Supports single and dual-panel monochrome Super Twisted Nematic (STN) displays
with 4 or 8-bit interfaces.
Supports single and dual-panel color STN displays.
Supports Thin Film Transistor (TFT) color displays.
Programmable display resolution including, but not limited to: 320x200, 320x240,
640x200, 640x240, 640x480, 800x600, and 1024x768.
Hardware cursor support for single-panel displays.
15 gray-level monochrome, 3375 color STN, and 32K color palettized TFT support.
1, 2, or 4 bits-per-pixel (bpp) palettized displays for monochrome STN.
1, 2, 4, or 8 bpp palettized color displays for color STN and TFT.
16 bpp true-color non-palettized, for color STN and TFT.
24 bpp true-color non-palettized, for color TFT.
Programmable timing for different display panels.
Section 12–6.12
(Table
Table
9–135), and PINSEL9
4–53,
Rev. 04 — 26 August 2009
Table
Table
9–145.
for power-up procedure.
12–263, and
(Table
4–63), set bit PCLCD.
(Table
(Table
Table
9–143).
12–260.
9–130), PINSEL3
(Table
© NXP B.V. 2009. All rights reserved.
(Table
User manual
9–145) and
9–133),
281 of 792