LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 625

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
UM10237_4
User manual
6.3 Count Control Register (T[0/1/2/3]CTCR - 0xE000 4070, 0xE000 8070,
Table 548: Timer Control Register (TCR, TIMERn: TnTCR - addresses 0xE000 4004,
0xE007 0070, 0xE007 4070)
The Count Control Register (CTCR) is used to select between Timer and Counter mode,
and in Counter mode to select the pin and edge(s) for counting.
When Counter Mode is chosen as a mode of operation, the CAP input (selected by the
CTCR bits 3:2) is sampled on every rising edge of the PCLK clock. After comparing two
consecutive samples of this CAP input, one of the following four events is recognized:
rising edge, falling edge, either of edges or no changes in the level of the selected CAP
input. Only if the identified event corresponds to the one selected by bits 1:0 in the CTCR
register, the Timer Counter register will be incremented.
Effective processing of the externally supplied clock to the counter has some limitations.
Since two successive rising edges of the PCLK clock are used to identify only one edge
on the CAP selected input, the frequency of the CAP input can not exceed one quarter of
the PCLK clock. Consequently, duration of the high/low levels on the same CAP input in
this case can not be shorter than 1/(2 PCLK).
Table 549: Count Control Register (T[0/1/2/3]CTCR - addresses 0xE000 4070, 0xE000 8070,
Bit
0
1
7:2
Bit
1:0
Symbol
Counter/
Timer
Mode
Symbol
Counter Enable When one, the Timer Counter and Prescale Counter are
Counter Reset
-
0xE000 8004, 0xE007 0004, 0xE007 4004) bit description
0xE007 0070, 0xE007 4070) bit description
Value
00
01
10
11
Rev. 04 — 26 August 2009
Description
enabled for counting. When zero, the counters are
disabled.
When one, the Timer Counter and the Prescale Counter
are synchronously reset on the next positive edge of
PCLK. The counters remain reset until TCR[1] is
returned to zero.
Reserved, user software should not write ones to
reserved bits. The value read from a reserved bit is not
defined.
Description
This field selects which rising PCLK edges can increment
Timer’s Prescale Counter (PC), or clear PC and increment
Timer Counter (TC).
Timer Mode: the TC is incremented when the Prescale
Counter matches the Prescale Register.
Timer Mode: every rising PCLK edge
Counter Mode: TC is incremented on rising edges on the
CAP input selected by bits 3:2.
Counter Mode: TC is incremented on falling edges on the
CAP input selected by bits 3:2.
Counter Mode: TC is incremented on both edges on the CAP
input selected by bits 3:2.
Chapter 24: LPC24XX Timer0/1/2/3
UM10237
© NXP B.V. 2009. All rights reserved.
Reset Value
0
0
NA
625 of 792
Reset
Value
00