LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 677

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
UM10237_4
User manual
5.1.1 Criterion for Valid User Code
5.1 Memory map after any reset
When ISP mode is entered after a power on reset, the IRC and PLL are used to generate
CCLK of 14.748 MHz. This may not be the case when ISP is invoked by the user
application (see
The Flash portion of the boot block is 8 kB in size and resides in the top portion (starting
from 0x0007 E000) of the on-chip Flash memory. After any reset the entire boot block is
also mapped to the top of the on-chip memory space i.e. the boot block is also visible in
the memory region starting from the address 0x7FFF E000. The Flash boot loader is
designed to run from this memory area, but both the ISP and IAP software use parts of the
on-chip RAM. The RAM usage is described later in this chapter. The interrupt vectors
residing in the boot block of the on-chip Flash memory also become active after reset, i.e.,
the bottom 64 bytes of the boot block are also visible in the memory region starting from
the address 0x0000 0000. The reset vector contains a jump instruction to the entry point
of the flash boot loader software.
Criterion for valid user code: The reserved ARM interrupt vector location (0x0000 0014)
should contain the 2’s complement of the check-sum of the remaining interrupt vectors.
This causes the checksum of all of the vectors together to be 0. The boot loader code
disables the overlaying of the interrupt vectors from the boot block, then checksums the
interrupt vectors in sector 0 of the Flash. If the signatures match then the execution
control is transferred to the user code by loading the program counter with 0x0000 0000.
Hence the user Flash reset vector should contain a jump instruction to the entry point of
the user application code.
Fig 138. Map of lower memory after reset
2.0 GB - 8 kB
0.0 GB
2.0 GB
Section 30–10.8 “Reinvoke ISP” on page
Rev. 04 — 26 August 2009
Chapter 30: LPC24XX Flash memory programming firmware
(RE-MAPPED FROM TOP OF FLASH MEMORY)
(BOOT BLOCK INTERRUPT VECTORS)
8 kB BOOT BLOCK RE-MAPPED TO
ACTIVE INTERRUPT VECTORS
HIGHER ADDRESS RANGE
ON-CHIP FLASH MEMORY
FROM THE BOOT BLOCK
8 kB BOOT BLOCK
695).
0x7FFF FFFF
0x7FFF E000
0x0007 FFFF
0x0007 E000
0x0000 0000
UM10237
© NXP B.V. 2009. All rights reserved.
677 of 792