LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 5

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
UM10237_4
User manual
•
•
•
•
•
•
•
•
•
•
•
•
•
•
– SPI controller.
– Two SSP controllers, with FIFO and multi-protocol capabilities. One is an alternate
– Three I
– I
Other peripherals:
– SD/MMC memory card interface.
– 160 general purpose I/O pins with configurable pull-up/down resistors.
– 10-bit ADC with input multiplexing among 8 pins.
– 10-bit DAC.
– Four general purpose timers/counters with 8 capture inputs and 10 compare
– Two PWM/timer blocks with support for three-phase motor control. Each PWM has
– Real-Time Clock (RTC) with separate power domain, clock source can be the RTC
– 2 kB SRAM powered from the RTC power pin, allowing data to be stored when the
– WatchDog Timer (WDT). The WDT can be clocked from the internal RC oscillator,
Standard ARM test/debug interface for compatibility with existing tools.
Emulation trace module supports real-time trace.
Single 3.3 V power supply (3.0 V to 3.6 V).
Four reduced power modes: idle, sleep, power-down, and deep power-down.
Four external interrupt inputs configurable as edge/level sensitive. All pins on PORT0
and PORT2 can be used as edge sensitive interrupt sources.
Processor wake-up from Power-down mode via any interrupt able to operate during
Power-down mode (includes external interrupts, RTC interrupt, USB activity, Ethernet
wake-up interrupt, CAN bus activity, PORT0/2 pin interrupt).
Two independent power domains allow fine tuning of power consumption based on
needed features.
Each peripheral has its own clock divider for further power saving. These dividers help
reducing active power by 20 - 30 %.
Brownout detect with separate thresholds for interrupt and forced reset.
On-chip power-on reset.
On-chip crystal oscillator with an operating range of 1 MHz to 24 MHz.
4 MHz internal RC oscillator trimmed to 1 % accuracy that can optionally be used as
the system clock. When used as the CPU clock, does not allow CAN and USB to run.
On-chip PLL allows CPU operation up to the maximum CPU rate without the need for
a high frequency crystal. May be run from the main oscillator, the internal RC
oscillator, or the RTC oscillator.
for the SPI port, sharing its interrupt. SSPs can be used with the GPDMA
controller.
the GPDMA.
outputs. Each timer block has an external count input.
an external count inputs.
oscillator or the APB clock.
rest of the chip is powered off.
the RTC oscillator, or the APB clock.
2
S (Inter-IC Sound) interface for digital audio input or output. It can be used with
2
C-bus interfaces (one with open-drain and two with standard port pins).
Rev. 04 — 26 August 2009
Chapter 1: LPC24XX Introductory information
UM10237
© NXP B.V. 2009. All rights reserved.
5 of 792