LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 664

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
UM10237_4
User manual
4.2 Watchdog Timer Constant Register (WDTC - 0xE000 0004)
4.3 Watchdog Feed Register (WDFEED - 0xE000 0008)
Table 585. Watchdog operating modes selection
Once the WDEN and/or WDRESET bits are set they can not be cleared by software. Both
flags are cleared by an external reset or a Watchdog timer underflow.
WDTOF The Watchdog time-out flag is set when the Watchdog times out. This flag is
cleared by software.
WDINT The Watchdog interrupt flag is set when the Watchdog times out. This flag is
cleared when any reset occurs. Once the watchdog interrupt is serviced, it can be
disabled in the VIC or the watchdog interrupt request will be generated indefinitely.
Table 586: Watchdog Mode register (WDMOD - address 0xE000 0000) bit description
The WDTC register determines the time-out value. Every time a feed sequence occurs
the WDTC content is reloaded in to the Watchdog timer. It’s a 32 bit register with 8 LSB
set to 1 on reset. Writing values below 0xFF will cause 0x0000 00FF to be loaded to the
WDTC. Thus the minimum time-out interval is T
Table 587: Watchdog Constant register (WDTC - address 0xE000 0004) bit description
Writing 0xAA followed by 0x55 to this register will reload the Watchdog timer with the
WDTC value. This operation will also start the Watchdog if it is enabled via the WDMOD
register. Setting the WDEN bit in the WDMOD register is not sufficient to enable the
Watchdog. A valid feed sequence must be completed after setting WDEN before the
Watchdog is capable of generating a reset. Until then, the Watchdog will ignore feed
WDEN
0
1
1
Bit
0
1
2
3
7:4
Bit
31:0
Symbol
WDEN
WDRESET WDRESET Watchdog reset enable bit (Set Only).
WDTOF
WDINT
-
Symbol
Count
WDRESET
X (0 or 1)
0
1
Description
WDEN Watchdog interrupt enable bit (Set Only).
WDTOF Watchdog time-out flag.
WDINT Watchdog interrupt flag (Read Only).
Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.
Description
Watchdog time-out interval.
Rev. 04 — 26 August 2009
Mode of Operation
Debug/Operate without the Watchdog running.
Watchdog interrupt mode: debug with the Watchdog interrupt but no
WDRESET enabled.
When this mode is selected, a watchdog counter underflow will set the
WDINT flag and the Watchdog interrupt request will be generated.
Watchdog reset mode: operate with the Watchdog interrupt and
WDRESET enabled.
When this mode is selected, a watchdog counter underflow will reset
the microcontroller. Although the Watchdog interrupt is also enabled in
this case (WDEN = 1) it will not be recognized since the watchdog
reset will clear the WDINT flag.
Chapter 27: LPC24XX WatchDog Timer (WDT)
WDCLK
× 256 × 4.
UM10237
© NXP B.V. 2009. All rights reserved.
0x0000 00FF
Reset Value
0
Reset Value
0
0
0 (Only after
external reset)
NA
664 of 792