EP1S20F780I6N Altera, EP1S20F780I6N Datasheet - Page 340

• Manufacturer Part Number: EP1S20F780I6N
• Description: IC STRATIX FPGA 20K LE 780-FBGA
• Manufacturer: Altera
• Series: Stratix®r

Specifications of EP1S20F780I6N

• Number Of Logic Elements/cells: 18460
• Number Of Labs/clbs: 1846
• Total Ram Bits: 1669248
• Number Of I /o: 586
• Voltage - Supply: 1.425 V ~ 1.575 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 780-FBGA
• Family Name: Stratix
• Number Of Logic Blocks/elements: 18460
• # I/os (max): 586
• Frequency (max): 450.05MHz
• Process Technology: 0.13um (CMOS)
• Operating Supply Voltage (typ): 1.5V
• Logic Cells: 18460
• Ram Bits: 1669248
• Operating Supply Voltage (min): 1.425V
• Operating Supply Voltage (max): 1.575V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 780
• Package Type: FC-FBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant

Enhanced PLLs
1–30
Stratix Device Handbook, Volume 2
CLK4p/n
CLK5p/n
CLK6p/n
CLK7p/n
CLK12p/n
CLK13p/n
CLK14p/n
CLK15p/n
PLL5_FBp/n
PLL6_FBp/n
PLLENABLE
Table 1–9. Enhanced PLL Pins (Part 1 of 2)
Pin
f
Single-ended or differential pins that can drive the inclk port for PLL 6.
Single-ended or differential pins that can drive the inclk port for PLL 6.
Single-ended or differential pins that can drive the inclk port for PLL 12.
Single-ended or differential pins that can drive the inclk port for PLL 12.
Single-ended or differential pins that can drive the inclk port for PLL 11.
Single-ended or differential pins that can drive the inclk port for PLL 11.
Single-ended or differential pins that can drive the inclk port for PLL 5.
Single-ended or differential pins that can drive the inclk port for PLL 5.
Single-ended or differential pins that can drive the fbin port for PLL 5.
Single-ended or differential pins that can drive the fbin port for PLL 6.
Dedicated input pin that drives the pllena port of all or a set of PLLs. If you do not
use this pin, connect it to ground.
With down-spread modulation, the peak of the modulated waveform is
the actual target frequency. Therefore, the system never exceeds the
maximum clock speed. To maintain reliable communication, the entire
system/subsystem should use the Stratix or Stratix GX device as the clock
source. Communication could fail if the Stratix or Stratix GX logic array
is clocked by the spread-spectrum clock, but the data it receives from
another device is not.
Since spread spectrum affects the m counter values, all spread-spectrum
PLL outputs are affected. Therefore, if only one spread-spectrum signal is
needed, the clock signal should use a separate PLL without other outputs
from that PLL.
No special considerations are needed when using spread spectrum with
the clock switchover feature. This is because the clock switchover feature
does not affect the m and n counter values, which are the counter values
that are switching when using spread spectrum.
PLL Reconfiguration
See AN 282: Implementing PLL Reconfiguration in Stratix & Stratix GX
Devices for information on PLL reconfiguration.
Enhanced PLL Pins
Table 1–9
PLLs. For inclk port connections to pins see
shows the physical pins and their purpose for the Enhanced
Description
“Clocking” on page
Altera Corporation
July 2005
1–39.