h8s-2635 Renesas Electronics Corporation., h8s-2635 Datasheet - Page 950
h8s-2635
Manufacturer Part Number
h8s-2635
Description
Renesas 16-bit Single-chip Microcomputer H8s Family/h8s/2600 Series
Manufacturer
Renesas Electronics Corporation.
Datasheet
1.H8S-2635.pdf
(1547 pages)
- Current page: 950 of 1547
- Download datasheet (10Mb)
Section 21C ROM (H8S/2635 Group)
Notes: 1. Mode pin and FWE pin input must satisfy the mode programming setup time (t
21C.8.2 User Program Mode
When set to user program mode, the chip can program and erase its flash memory by executing a
user program/erase control program. Therefore, on-board reprogramming of the on-chip flash
memory can be carried out by providing on-board means of FWE control and supply of
programming data, and storing a program/erase control program in part of the program area as
necessary.
Rev. 6.00 Feb 22, 2005 page 890 of 1484
REJ09B0103-0600
Before branching to the programming control program (RAM area H'FFE000), the chip
terminates transmit and receive operations by the on-chip SCI (channel 1) (by clearing the RE
and TE bits in SCR to 0), but the adjusted bit rate value remains set in BRR. The transmit data
output pin, TxD1, goes to the high-level output state (P33DDR = 1, P33DR = 1).
The contents of the CPU’s internal general registers are undefined at this time, so these
registers must be initialized immediately after branching to the programming control program.
In particular, since the stack pointer (SP) is used implicitly in subroutine calls, etc., a stack area
must be specified for use by the programming control program.
The initial values of other on-chip registers are not changed.
Boot mode can be entered by making the pin settings shown in table 21C-9 and executing a
reset-start.
Boot mode can be cleared by driving the reset pin low, waiting at least 20 states, then setting
the FWE pin and mode pins, and executing reset release *
WDT overflow reset.
Do not change the mode pin input levels in boot mode, and do not drive the FWE pin low
while the boot program is being executed or while flash memory is being programmed or
erased *
If the mode pin input levels are changed (for example, from low to high) during a reset, the
state of ports with multiplexed address functions and bus control output pins (
will change according to the change in the microcomputer’s operating mode *
Therefore, care must be taken to make pin settings to prevent these pins from becoming output
signal pins during a reset, or to prevent collision with signals outside the microcomputer.
2. For precautions on applying and disconnecting FWE, see section 21C.15, Flash
3. See Appendix D, Pin States.
2
states) with respect to the reset release timing.
Memory Programming and Erasing Precautions.
.
1
. Boot mode can also be cleared by a
3
A S
.
,
R D
,
MDS
H W R
= 4
)
Related parts for h8s-2635
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Renesas 16-bit Single-chip Microcomputer H8s Family/h8s/2100 Series
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 16-bit Single-chip Microcomputer H8s Family/h8s/2100 Series
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 16-bit Single-chip Microcomputer H8s Family/h8s/2100 Series
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 16-bit Single-chip Microcomputer H8s Family/h8s/2100 Series
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 16-bit Single-chip Microcomputer H8s Family / H8s/2100 Series
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 16-bit Single-chip Microcomputer H8s Family/h8s/2100 Series
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 16-bit Single-chip Microcomputer H8s Family H8s-2100 Series
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 16-bit Single-chip Microcomputer H8s Family/h8s/2600 Series
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 16-bit Single-chip Microcomputer H8s Family/h8s/2600 Series
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 16-bit Single-chip Microcomputer H8s Family/h8s/2600 Series
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas Technology Corp [Renesas 32-Bit RISC Microcomputer Super RISC engine Family/SH7700 Series]
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
RENESAS MCU M16C FAMILY / M16C/Tiny SERIES
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas Starter Kit for RX210
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas StarterKit for RX630
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas Starter Kit+ for RX63N
Manufacturer:
Renesas Electronics Corporation.