MC9S12E128CPVE Freescale Semiconductor, MC9S12E128CPVE Datasheet - Page 445

• Manufacturer Part Number: MC9S12E128CPVE
• Description: IC MCU 128K FLASH 25MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12E128CPVE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.75 V
• Data Converters: A/D 16x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Processor Series: S12E
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 92
• Number Of Timers: 12
• Operating Supply Voltage: 3.135 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• On-chip Dac: 2-ch x 8-bit
• Controller Family/series: HCS12/S12X
• No. Of I/o's: 90
• Ram Memory Size: 8KB
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• For Use With: M68EVB912E128 - BOARD EVAL FOR MC9S12E128/64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

14.5
This subsection describes how VREG3V3V2 controls the reset of the MCU.The reset values of registers
and signals are provided in
are listed in
14.5.1
During chip power-up the digital core may not work if its supply voltage V
deassertion level (V
kept high until V
continues the start-up sequence. The power-on reset is active in all operation modes of VREG3V3V2.
14.5.2
For details on low-voltage reset see
14.6
This subsection describes all interrupts originated by VREG3V3V2.
The interrupt vectors requested by VREG3V3V2 are listed in
priorities are defined at MCU level.
14.6.1
In FPM VREG3V3V2 monitors the input voltage V
status bit LVDS is set to 1. Vice versa, LVDS is reset to 0 when V
interrupt, indicated by flag LVIF = 1, is triggered by any change of the status bit LVDS if interrupt enable
bit LVIE = 1.
Freescale Semiconductor
Resets
Interrupts
Power-On Reset
Low-Voltage Reset
LVI — Low-Voltage Interrupt
Table
Low Voltage Interrupt (LVI)
On entering the reduced-power mode, the LVIF is not cleared by the
VREG3V3V2.
Power-on reset
Low-voltage reset
DD
14-4.
PORD
Interrupt Source
exceeds V
Reset Source
). Therefore, signal POR which forces the other blocks of the device into reset is
Section 14.3, “Memory Map and Register
PORD
Table 14-5. VREG3V3V2 — Interrupt Vectors
Table 14-4. VREG3V3V2 — Reset Sources
Section 14.4.6, “LVR — Low-Voltage
. Then POR becomes low and the reset generator of the device
MC9S12E128 Data Sheet, Rev. 1.07
Always active
Available only in full-performance mode
LVIE = 1; Available only in full-performance mode
NOTE
DDA
. Whenever V
Local Enable
Chapter 14 Dual Output Voltage Regulator (VREG3V3V2)
Local Enable
Table
DDA
14-5. Vector addresses and interrupt
Definition”. Possible reset sources
DDA
rises above level V
drops below level V
DD
Reset”.
is below the POR
LVID
. An
LVIA
the
445