C8051F302 Silicon Laboratories Inc, C8051F302 Datasheet - Page 139

• Manufacturer Part Number: C8051F302
• Description: IC 8051 MCU 8K FLASH 11MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F30xr

Specifications of C8051F302

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 8
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 11-VQFN
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SMBus, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 8
• Number Of Timers: 16 bit
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No

Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bits1-0:
R/W
Bit7
-
UNUSED. Read = 0b, Write = don’t care.
T2MH: Timer 2 High Byte Clock Select
This bit selects the clock supplied to the Timer 2 high byte if Timer 2 is configured in split 8-bit timer
mode. T2MH is ignored if Timer 2 is in any other mode.
0: Timer 2 high byte uses the clock defined by the T2XCLK bit in TMR2CN.
1: Timer 2 high byte uses the system clock.
T2ML: Timer 2 Low Byte Clock Select
This bit selects the clock supplied to Timer 2. If Timer 2 is configured in split 8-bit timer mode, this
bit selects the clock supplied to the lower 8-bit timer.
0: Timer 2 low byte uses the clock defined by the T2XCLK bit in TMR2CN.
1: Timer 2 low byte uses the system clock.
T1M: Timer 1 Clock Select.
This select the clock source supplied to Timer 1. T1M is ignored when C/T1 is set to logic 1.
0: Timer 1 uses the clock defined by the prescale bits, SCA1-SCA0.
1: Timer 1 uses the system clock.
T0M: Timer 0 Clock Select.
This bit selects the clock source supplied to Timer 0. T0M is ignored when C/T0 is set to logic 1.
0: Counter/Timer 0 uses the clock defined by the prescale bits, SCA1-SCA0.
1: Counter/Timer 0 uses the system clock.
UNUSED. Read = 0b, Write = don’t care.
SCA1-SCA0: Timer 0/1 Prescale Bits
These bits control the division of the clock supplied to Timer 0 and/or Timer 1 if configured to use
prescaled clock inputs.
Note: External clock divided by 8 is synchronized with the
system clock, and the external clock must be less than or
equal to the system clock to operate in this mode.
SCA1
T2MH
0
0
1
1
R/W
Bit6
SCA0
Figure 15.6. CKCON: Clock Control Register
0
1
0
1
T2ML
R/W
Bit5
Prescaled Clock
System clock divided by 12
System clock divided by 48
External clock divided by 8
System clock divided by 4
T1M
R/W
Bit4
T0M
R/W
Bit3
Rev. 2.3
R/W
Bit2
-
C8051F300/1/2/3/4/5
SCA1
R/W
Bit1
SCA0
R/W
Bit0
SFR Address:
00000000
Reset Value
0x8E
139