R5F211B1SP#U0 Renesas Electronics America, R5F211B1SP#U0 Datasheet - Page 83

• Manufacturer Part Number: R5F211B1SP#U0
• Description: IC R8C MCU FLASH 4K 20SSOP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/R8C/Tiny/1Br

Specifications of R5F211B1SP#U0

• Core Processor: R8C
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, SIO, SSU, UART/USART
• Peripherals: LED, POR, Voltage Detect, WDT
• Number Of I /o: 13
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 20-SSOP
• For Use With: R0K5211B4S001BE - KIT STARTER FOR R8C/18191A1BR0K5211B4S000BE - KIT DEV EVALUATION R8C/1BR0E521174CPE10 - EMULATOR COMPACT R8C/18/19/1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/1A Group, R8C/1B Group
Rev.1.30
REJ09B0252-0130
The clocks generated by the clock generation circuits are described below.
10.1
Figure 10.7
This clock is supplied by a main clock oscillation circuit. This clock is used as the clock source for the CPU and
peripheral function clocks. The main clock oscillation circuit is configured by connecting a resonator between the
XIN and XOUT pins. The main clock oscillation circuit includes an on-chip feedback resistor, which is
disconnected from the oscillation circuit in stop mode in order to reduce the amount of power consumed by the
chip. The main clock oscillation circuit may also be configured by feeding an externally generated clock to the XIN
pin. Figure 10.7 shows Examples of Main Clock Connection Circuit. During reset and after reset, the main clock
stops.
The main clock starts oscillating when the CM05 bit in the CM0 register is set to 0 (main clock on) after setting the
CM13 bit in the CM1 register to 1 (XIN- XOUT pin).
To use the main clock for the CPU clock source, set the OCD2 bit in the OCD register to 0 (selects main clock)
after the main clock is oscillating stably.
The power consumption can be reduced by setting the CM05 bit in the CM0 register to 1 (main clock stops) if the
OCD2 bit is set to 1 (select on-chip oscillator clock).
When an external clock is input to the XIN pin, the main clock does not stop if the CM05 bit is set to 1. If
necessary, use an external circuit to stop the clock.
In stop mode, all clocks including the main clock stop. Refer to 10.4 Power Control for details.
Main Clock
Dec 08, 2006
Ceramic resonator external circuit
NOTE :
1. Insert a damping resistor if required. The resistance will vary depending on the oscillator and the oscillation drive
(on-chip feedback resistor)
XIN
capacity setting. Use the value recommended by the manufacturer of the oscillator.
When the oscillation drive capacity is set to low, check that oscillation is stable. Also, if the oscillator manufacturer's
data sheet specifies that a feedback resistor be added to the chip externally, insert a feedback resistor between XIN
and XOUT following the instructions.
Examples of Main Clock Connection Circuit
CIN
MCU
Page 65 of 315
XOUT
Rd
COUT
(1)
VCC
VSS
Externally derived clock
External clock input circuit
(on-chip feedback resistor)
XIN
MCU
10. Clock Generation Circuit
XOUT
Open