UPD78F0550MA-FAA-AX Renesas Electronics America, UPD78F0550MA-FAA-AX Datasheet - Page 271

• Manufacturer Part Number: UPD78F0550MA-FAA-AX
• Description: MCU 8BIT 16-SSOP
• Manufacturer: Renesas Electronics America
• Series: 78K0/Kx2-Lr

Specifications of UPD78F0550MA-FAA-AX

• Package / Case: *
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 10MHz
• Number Of I /o: 12
• Core Processor: 78K/0
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Program Memory Size: 4KB (4K x 8)
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Peripherals: LVD, POR, PWM, WDT
• Connectivity: I²C, LIN, UART/USART
• Core Size: 8-Bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

(1) Measuring the pulse width by using two input signals of the TI000 and TI010 pins (free-running timer
A pulse width can be measured in the following three ways.
Remarks 1. For the setting of the I/O pins, refer to 6.3 (5) Port mode register 0 (PM0).
mode)
Set the free-running timer mode (TMC003 and TMC002 = 01). When the valid edge of the TI000 pin is detected,
the count value of TM00 is captured to CR010. When the valid edge of the TI010 pin is detected, the count value
of TM00 is captured to CR000. Specify detection of both the edges of the TI000 and TI010 pins.
By this measurement method, the previous count value is subtracted from the count value captured by the edge
of each input signal. Therefore, save the previously captured value to a separate register in advance.
If an overflow occurs, the value becomes negative if the previously captured value is simply subtracted from the
current captured value and, therefore, a borrow occurs (bit 0 (CY) of the program status word (PSW) is set to 1).
If this happens, ignore CY and take the calculated value as the pulse width. In addition, clear bit 0 (OVF00) of
16-bit timer mode control register 00 (TMC00) to 0.
Measuring the pulse width by using two input signals of the TI000 and TI010 pins (free-running timer mode)
Measuring the pulse width by using one input signal of the TI000 pin (free-running timer mode)
Measuring the pulse width by using one input signal of the TI000 pin (clear & start mode entered by the TI000 pin
valid edge input)
Capture trigger input
Capture trigger input
(TMC003, TMC002)
Capture interrupt
Capture interrupt
Capture register
Capture register
TM00 register
Operable bits
Overflow flag
(INTTM010)
(INTTM000)
2. For how to enable the INTTM000 signal interrupt, refer to CHAPTER 17 INTERRUPT FUNCTIONS.
(OVF00)
(CR010)
(CR000)
(TI000)
(TI010)
FFFFH
0000H
Figure 6-48. Timing Example of Pulse Width Measurement (1)
0000H
0000H
00
CHAPTER 6 16-BIT TIMER/EVENT COUNTER 00
A
TMC00 = 04H, PRM00 = F0H, CRC00 = 05H
01
M
Preliminary User’s Manual U19111EJ2V1UD
A
B
0 write clear
M
N
B
0 write clear
N
C
S
C
0 write clear
D
S
P
D
P
0 write clear
E
Q
E
Q
271