DF70844AD80FPV Renesas Electronics America, DF70844AD80FPV Datasheet - Page 269

• Manufacturer Part Number: DF70844AD80FPV
• Description: IC SUPERH MCU FLASH 112LQFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7080r

Specifications of DF70844AD80FPV

• Core Size: 32-Bit
• Program Memory Size: 256KB (256K x 8)
• Core Processor: SH-2
• Speed: 80MHz
• Connectivity: EBI/EMI, FIFO, I²C, SCI, SSU
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• No. Of I/o's: 76
• Ram Memory Size: 16KB
• Cpu Speed: 80MHz
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 3V To 3.6V, 4.5V To 5.5V
• Embedded Interface Type: I2C, SCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K570865S001BE - KIT STARTER FOR SH7086R0K570865S000BE - KIT STARTER FOR SH7086HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

8.7
8.7.1
An example is shown in which the DTC is used to receive 128 bytes of data via the SCI.
1. Set MRA to fixed source address (SM1 = SM0 = 0), incrementing destination address (DM1 =
2. Set the start address of the transfer information for an RXI interrupt at the DTC vector address.
3. Set the corresponding bit in DTCER to 1.
4. Set the SCI to the appropriate receive mode. Set the RIE bit in SCR to 1 to enable the receive
5. Each time reception of one byte of data ends on the SCI, the RDRF flag in SSR is set to 1, an
6. When CRA becomes 0 after the 128 data transfers have ended, the RDRF flag is held at 1, the
8.7.2
By executing a second data transfer and performing re-setting of the first data transfer only when
the counter value is 0, it is possible to perform 256 or more repeat transfers.
An example is shown in which a 128-kbyte input buffer is configured. The input buffer is assumed
to have been set to start at lower address H'0000. Figure 8.19 shows the chain transfer when the
counter value is 0.
1. For the first transfer, set the normal transfer mode for input data. Set the fixed transfer source
2. Prepare the upper 8-bit addresses of the start addresses for 65,536-transfer units for the first
1, DM0 = 0), normal transfer mode (MD1 = MD0 = 0), and byte size (Sz1 = Sz0 = 0). The
DTS bit can have any value. Set MRB for one data transfer by one interrupt (CHNE = 0,
DISEL = 0). Set the RDR address of the SCI in SAR, the start address of the RAM area where
the data will be received in DAR, and 128 (H'0080) in CRA. CRB can be set to any value.
end (RXI) interrupt. Since the generation of a receive error during the SCI reception operation
will disable subsequent reception, the CPU should be enabled to accept receive error
interrupts.
RXI interrupt is generated, and the DTC is activated. The receive data is transferred from RDR
to RAM by the DTC. DAR is incremented and CRA is decremented. The RDRF flag is
automatically cleared to 0.
DTCE bit is cleared to 0, and an RXI interrupt request is sent to the CPU. Termination
processing should be performed in the interrupt handling routine.
address, CRA = H'0000 (65,536 times), CHNE = 1, CHNS = 1, and DISEL = 0.
data transfer in a separate area (in ROM, etc.). For example, if the input buffer is configured at
addresses H'200000 to H'21FFFF, prepare H'21 and H'20.
Examples of Use of the DTC
Normal Transfer Mode
Chain Transfer when Counter = 0
Rev. 3.00 May 17, 2007 Page 211 of 1582
Section 8 Data Transfer Controller (DTC)
REJ09B0181-0300