DF70844AD80FPV Renesas Electronics America, DF70844AD80FPV Datasheet - Page 699

• Manufacturer Part Number: DF70844AD80FPV
• Description: IC SUPERH MCU FLASH 112LQFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7080r

Specifications of DF70844AD80FPV

• Core Size: 32-Bit
• Program Memory Size: 256KB (256K x 8)
• Core Processor: SH-2
• Speed: 80MHz
• Connectivity: EBI/EMI, FIFO, I²C, SCI, SSU
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• No. Of I/o's: 76
• Ram Memory Size: 16KB
• Cpu Speed: 80MHz
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 3V To 3.6V, 4.5V To 5.5V
• Embedded Interface Type: I2C, SCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K570865S001BE - KIT STARTER FOR SH7086R0K570865S000BE - KIT STARTER FOR SH7086HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

11.8.4
• When making a transition to a mode (Normal, PWM1, PWM2, PCM) in which the pin output
• In PWM mode 1, since a waveform is not output to the TIOC*B (TIOC *D) pin, setting TIOR
• In PWM mode 2, since a waveform is not output to the cycle register pin, setting TIOR will
• In normal mode or PWM mode 2, if TGRC and TGRD operate as buffer registers, setting
• In PWM mode 1, if either TGRC or TGRD operates as a buffer register, setting TIOR will not
• When making a transition to a mode (CPWM, RPWM) in which the pin output level is
Note: Channel number is substituted for * indicated in this article.
level is selected by the timer I/O control register (TIOR) setting, initialize the pins by means of
a TIOR setting.
will not initialize the pins. If initialization is required, carry it out in normal mode, then switch
to PWM mode 1.
not initialize the pins. If initialization is required, carry it out in normal mode, then switch to
PWM mode 2.
TIOR will not initialize the buffer register pins. If initialization is required, clear buffer mode,
carry out initialization, then set buffer mode again.
initialize the TGRC pin. To initialize the TGRC pin, clear buffer mode, carry out initialization,
then set buffer mode again.
selected by the timer output control register (TOCR) setting, switch to normal mode and
perform initialization with TIOR, then restore TIOR to its initial value, and temporarily disable
channel 3 and 4 output with the timer output master enable register (TOER). Then operate the
unit in accordance with the mode setting procedure (TOCR setting, TMDR setting, TOER
setting).
Overview of Initialization Procedures and Mode Transitions in Case of Error
during Operation, etc.
Section 11 Multi-Function Timer Pulse Unit 2 (MTU2)
Rev. 3.00 May 17, 2007 Page 641 of 1582
REJ09B0181-0300