NH82801HEM S LB9B Intel, NH82801HEM S LB9B Datasheet - Page 143
![no-image](/images/manufacturer_photos/0/3/336/intel_sml.jpg)
NH82801HEM S LB9B
Manufacturer Part Number
NH82801HEM S LB9B
Description
Manufacturer
Intel
Datasheet
1.NH82801HEM_S_LB9B.pdf
(890 pages)
Specifications of NH82801HEM S LB9B
Lead Free Status / RoHS Status
Compliant
- Current page: 143 of 890
- Download datasheet (7Mb)
Functional Description
5.8.4
5.8.4.1
5.8.4.2
5.8.4.3
5.8.4.4
Intel
®
ICH8 Family Datasheet
Modes of Operation
Fully Nested Mode
In this mode, interrupt requests are ordered in priority from 0 through 7, with 0 being
the highest. When an interrupt is acknowledged, the highest priority request is
determined and its vector placed on the bus. Additionally, the ISR for the interrupt is
set. This ISR bit remains set until: the processor issues an EOI command immediately
before returning from the service routine; or if in AEOI mode, on the trailing edge of
the second INTA#. While the ISR bit is set, all further interrupts of the same or lower
priority are inhibited, while higher levels generate another interrupt. Interrupt priorities
can be changed in the rotating priority mode.
Special Fully-Nested Mode
This mode is used in the case of a system where cascading is used, and the priority has
to be conserved within each slave. In this case, the special fully-nested mode is
programmed to the master controller. This mode is similar to the fully-nested mode
with the following exceptions:
Automatic Rotation Mode (Equal Priority Devices)
In some applications, there are a number of interrupting devices of equal priority.
Automatic rotation mode provides for a sequential 8-way rotation. In this mode, a
device receives the lowest priority after being serviced. In the worst case, a device
requesting an interrupt has to wait until each of seven other devices are serviced at
most once.
There are two ways to accomplish automatic rotation using OCW2; the Rotation on
Non-Specific EOI Command (R=1, SL=0, EOI=1) and the rotate in automatic EOI mode
which is set by (R=1, SL=0, EOI=0).
Specific Rotation Mode (Specific Priority)
Software can change interrupt priorities by programming the bottom priority. For
example, if IRQ5 is programmed as the bottom priority device, then IRQ6 is the highest
priority device. The Set Priority Command is issued in OCW2 to accomplish this, where:
R=1, SL=1, and LO–L2 is the binary priority level code of the bottom priority device.
In this mode, internal status is updated by software control during OCW2. However, it
is independent of the EOI command. Priority changes can be executed during an EOI
command by using the Rotate on Specific EOI Command in OCW2 (R=1, SL=1, EOI=1
and LO–L2=IRQ level to receive bottom priority.
• When an interrupt request from a certain slave is in service, this slave is not locked
• When exiting the Interrupt Service routine, software has to check whether the
out from the master's priority logic and further interrupt requests from higher
priority interrupts within the slave are recognized by the master and initiate
interrupts to the processor. In the normal-nested mode, a slave is masked out
when its request is in service.
interrupt serviced was the only one from that slave. This is done by sending a Non-
Specific EOI command to the slave and then reading its ISR. If it is 0, a non-
specific EOI can also be sent to the master.
143
Related parts for NH82801HEM S LB9B
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![NH82801HEM S LA5R](/images/manufacturer_photos/0/3/336/intel_tmb.jpg)
Part Number:
Description:
Manufacturer:
Intel
Datasheet:
![RJ80535VC600512](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Microprocessor: Intel Celeron M Processor 320 and Ultra Low Voltage Intel Celeron M Processor at 600MHz
Manufacturer:
Intel Corporation
![82550GY](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Datasheet:
![DA28F320J5-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
![E28F320J5-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
![G28F640J5-150](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 64 Mbit. Access speed 150 ns
Manufacturer:
Intel Corporation
Datasheet:
![E28F320J5-100](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 100 ns
Manufacturer:
Intel Corporation
Datasheet:
![DA28F640J5A-150](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
DA28F640J5A-1505 Volt Intel StrataFlash Memory
Manufacturer:
Intel Corporation
Datasheet:
![DA28F320J5A-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Datasheet:
![E28F320J5A-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
![NHE6300ESB](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel 6300ESB I/O Controller Hub
Manufacturer:
Intel Corporation
Datasheet:
![NH82801DB](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel 82801DB I/O Controller Hub (ICH4), Pb-Free SLI
Manufacturer:
Intel Corporation
Datasheet: