Z32AN00NW200SG Zilog, Z32AN00NW200SG Datasheet - Page 178

• Manufacturer Part Number: Z32AN00NW200SG
• Description: IC ARM922T MCU 200MHZ 256-BGA
• Manufacturer: Zilog
• Series: Encore!® 32r

Specifications of Z32AN00NW200SG

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 200MHz
• Connectivity: EBI/EMI, IrDA, SmartCard, SPI, UART/USART, USB OTG
• Peripherals: DMA, LCD, Magnetic Card Reader, POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Type: ROMless
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.71 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-LBGA
• For Use With: 269-4713 - KIT DEV ENCORE 32 SERIES
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Other names: 269-4717

Z32AN Series Data Sheet
19.8.7 Offset 018h: USB_OTG_STAT – OTG Status Register
19.8.8 Offset 01Ch: USB_OTG_CTL – OTG Control Register
DS0200-003
31:08
Bits
31:08
07
06
05
04
03
02
01
00
Bits
06
05
04
02
07
03
01
00
“
Type
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Type
RO
RO
RO
RW
RW
RW
RW
RO
Reset
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Description
Reserved
ID: When set, either no cable is attached or a Type B cable has been plugged into the
USB connector.
connector.
MS1: This bit is reserved for the 1ms count, but is not useful to software.
LINE_STATE:
previous 1ms, and can be considered de-bounced.
Reserved
BSESSV: Set when V
BSESSE: Set when V
Reserved
AVBUSV: This bit will be set when V
D- High (DMH): When set, enables a pull-up resistor on D-.
D+ Low (DPL): When set, enables a pull-down resistor on D+.
D- Low (DML): When set, enables a pull-down resistor on D-.
On the Go Enable (EN): Only valid if USB_CTRL.EN is set. When set, pull-up and
pull-down controls in this register are used.
cleared, D+ pull up is engaged. When cleared and USB_CTRL.HOST is set, D+ and D-
pull down resistors are engaged if the controller is enabled and in host mode.
Description
Reserved
D+ High (DPH): When set, enables a pull-up resistor on D+.
V
V
V
BUS
BUS
BUS
On (VBUS_ON): When set, this will turn on V
Charge (VBUSC): When set, charges VBUS through a resistor.
Discharge (VBUSD): When set, discharges VBUS through a resistor.
Set when USB_CTRL.J and USB_CTRL.SE0 have been static for the
When cleared, a Type A cable has been plugged into the USB
BUS
BUS
is below the “B” session end threshold.
is above the “B” session valid threshold.
BUS
is above the “A” VBUS Valid threshold.
When cleared and USB_CTRL.HOST is
BUS
Page 165