DF70844AD80FPV Renesas Electronics America, DF70844AD80FPV Datasheet - Page 1397

• Manufacturer Part Number: DF70844AD80FPV
• Description: IC SUPERH MCU FLASH 112LQFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7080r

Specifications of DF70844AD80FPV

• Core Size: 32-Bit
• Program Memory Size: 256KB (256K x 8)
• Core Processor: SH-2
• Speed: 80MHz
• Connectivity: EBI/EMI, FIFO, I²C, SCI, SSU
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• No. Of I/o's: 76
• Ram Memory Size: 16KB
• Cpu Speed: 80MHz
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 3V To 3.6V, 4.5V To 5.5V
• Embedded Interface Type: I2C, SCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K570865S001BE - KIT STARTER FOR SH7086R0K570865S000BE - KIT STARTER FOR SH7086HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

26.5
26.5.1
This LSI switches from a program execution state to software standby mode by executing the
SLEEP instruction when the STBY bit in STBCR1 and the STBYMD bit in STBCR6 are set to 1.
However, software standby mode cannot be entered when the bus is released (low-level input to
BREQ pin). Execute the SLEEP instruction after halting the DMAC and DTC. In software
standby mode, not only the CPU but also the clock and on-chip peripheral modules halt.
The contents of the CPU registers and the data of the on-chip RAM remain unchanged. Some
registers of on-chip peripheral modules are, however, initialized. For details on the states of on-
chip peripheral module registers in software standby mode, refer to section 27.3, Register States in
Each Operating Mode. For details on the pin states in software standby mode, refer to appendix A,
Pin States.
The procedure for switching to software standby mode is as follows:
1. Clear the TME bit in the timer control register (WTCSR) of the WDT to 0 to stop the WDT.
2. Set the timer counter (WTCNT) of the WDT to 0 and bits CKS2 to CKS0 in WTCSR to
3. If the DMAC and DTC are operating, stop their operation.
4. If the bus is released (low-level input to BREQ pin), acquire the bus mastership (high-level
5. After setting the STBY bit in STBCR1 and the STBYMD bit in STBCR6 to 1, execute the
6. Software standby mode is entered and the clocks within this LSI are halted.
appropriate values to secure the specified oscillation settling time.
input to BREQ pin).
SLEEP instruction.
Software Standby Mode
Transition to Software Standby Mode
Rev. 3.00 May 17, 2007 Page 1339 of 1582
Section 26 Power-Down Modes
REJ09B0181-0300