XC3S200-4TQG144I Xilinx Inc, XC3S200-4TQG144I Datasheet - Page 101

• Manufacturer Part Number: XC3S200-4TQG144I
• Description: FPGA Spartan®-3 Family 200K Gates 4320 Cells 630MHz 90nm Technology 1.2V 144-Pin TQFP
• Manufacturer: Xilinx Inc
• Series: Spartan™-3r

Specifications of XC3S200-4TQG144I

• Package: 144TQFP
• Family Name: Spartan®-3
• Device Logic Units: 4320
• Device System Gates: 200000
• Maximum Internal Frequency: 630 MHz
• Typical Operating Supply Voltage: 1.2 V
• Maximum Number Of User I/os: 97
• Ram Bits: 221184
• Package / Case: 144-TQFP, 144-VQFP
• Mounting Type: Surface Mount
• Voltage - Supply: 1.14 V ~ 3.465 V
• Operating Temperature: -40°C ~ 100°C
• Number Of I /o: 97
• Number Of Logic Elements/cells: *
• Number Of Gates: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 69: Spartan-3 FPGA Pin Definitions
DS099-4 (v2.5) December 4, 2009
Product Specification
I/O: General-purpose I/O pins
I/O
I/O_Lxxy_#
DUAL: Dual-purpose configuration pins
IO_Lxxy_#/DIN/D0,
IO_Lxxy_#/D1,
IO_Lxxy_#/D2,
IO_Lxxy_#/D3,
IO_Lxxy_#/D4,
IO_Lxxy_#/D5,
IO_Lxxy_#/D6,
IO_Lxxy_#/D7
IO_Lxxy_#/CS_B
IO_Lxxy_#/RDWR_B
IO_Lxxy_#/
BUSY/DOUT
Pin Name
R
User-defined as input,
output, bidirectional,
three-state output,
open-drain output,
open-source output
User-defined as input,
output, bidirectional,
three-state output,
open-drain output,
open-source output
Input during configuration
Possible bidirectional I/O
after configuration if
SelectMap port is retained
Otherwise, user I/O after
configuration
Input during Parallel mode
configuration
Possible input after
configuration if SelectMap
port is retained
Otherwise, user I/O after
configuration
Input during Parallel mode
configuration
Possible input after
configuration if SelectMap
port is retained
Otherwise, user I/O after
configuration
Output during configuration
Possible output after
configuration if SelectMap
port is retained
Otherwise, user I/O after
configuration
Direction
www.xilinx.com
User I/O:
Unrestricted single-ended user-I/O pin. Supports all I/O standards
except the differential standards.
User I/O, Half of Differential Pair:
Unrestricted single-ended user-I/O pin or half of a differential pair.
Supports all I/O standards including the differential standards.
Configuration Data Port:
In Parallel (SelectMAP) modes, D0-D7 are byte-wide configuration
data pins. These pins become user I/Os after configuration unless
the SelectMAP port is retained via the Persist bitstream option.
In Serial modes, DIN (D0) serves as the single configuration data
input. This pin becomes a user I/O after configuration unless
retained by the Persist bitstream option.
Chip Select for Parallel Mode Configuration:
In Parallel (SelectMAP) modes, this is the active-Low Chip Select
signal. This pin becomes a user I/O after configuration unless the
SelectMAP port is retained via the Persist bitstream option.
Read/Write Control for Parallel Mode Configuration:
In Parallel (SelectMAP) modes, this is the active-Low Write
Enable, active-High Read Enable signal. This pin becomes a user
I/O after configuration unless the SelectMAP port is retained via
the Persist bitstream option.
Configuration Data Rate Control for Parallel Mode, Serial Data
Output for Serial Mode:
In Parallel (SelectMAP) modes, BUSY throttles the rate at which
configuration data is loaded. This pin becomes a user I/O after
configuration unless the SelectMAP port is retained via the Persist
bitstream option.
In Serial modes, DOUT provides preamble and configuration data
to downstream devices in a multi-FPGA daisy-chain. This pin
becomes a user I/O after configuration.
Spartan-3 FPGA Family: Pinout Descriptions
Description
101