NH82801GHM S L8YR Intel, NH82801GHM S L8YR Datasheet - Page 218
NH82801GHM S L8YR
Manufacturer Part Number
NH82801GHM S L8YR
Description
Manufacturer
Intel
Datasheet
1.NH82801GHM_S_L8YR.pdf
(848 pages)
Specifications of NH82801GHM S L8YR
Lead Free Status / RoHS Status
Compliant
- Current page: 218 of 848
- Download datasheet (7Mb)
5.20.10.1.3
218
Enabling the Debug Port
There are two mutually exclusive conditions that debug software must address as part
of its startup processing:
Debug software can determine the current ‘initialized’ state of the EHCI by examining
the Configure Flag in the EHCI USB 2.0 Command Register. If this flag is set, then
system software has initialized the EHCI. Otherwise the EHCI should not be considered
initialized. Debug software will initialize the debug port registers depending on the
state the EHCI. However, before this can be accomplished, debug software must
determine which root USB port is designated as the debug port.
Determining the Debug Port
Debug software can easily determine which USB root port has been designated as the
debug port by examining bits 20:23 of the EHCI Host Controller Structural Parameters
register. This 4-bit field represents the numeric value assigned to the debug port (i.e.,
0001=port 0).
Debug Software Startup with Non-Initialized EHCI
Debug software can attempt to use the debug port if after setting the OWNER_CNT bit,
the Current Connect Status bit in the appropriate (See Determining the Debug Port)
PORTSC register is set. If the Current Connect Status bit is not set, then debug
software may choose to terminate or it may choose to wait until a device is connected.
If a device is connected to the port, then debug software must reset/enable the port.
Debug software does this by setting and then clearing the Port Reset bit the PORTSC
register. To ensure a successful reset, debug software should wait at least 50 ms before
clearing the Port Reset bit. Due to possible delays, this bit may not change to 0
immediately; reset is complete when this bit reads as 0. Software must not continue
until this bit reads 0.
If a high-speed device is attached, the EHCI will automatically set the Port Enabled/
Disabled bit in the PORTSC register and the debug software can proceed. Debug
software should set the ENABLED_CNT bit in the Debug Port Control/Status register,
and then reset (clear) the Port Enabled/Disabled bit in the PORTSC register (so that the
system host controller driver does not see an enabled port when it is first loaded).
Debug Software
5. If valid packet was received from the device that was more than one byte in length
6. If no valid packet is received, then the debug port controller:
• The EHCI has been initialized by system software
• The EHCI has not been initialized by system software
(indicating it was a data packet), then the debug port controller:
— Transmits an ACK handshake packet
— Resets the ERROR_GOOD#_STS bit
— Sets the DONE_STS bit
— Sets the EXCEPTION_STS field to 001b
— Sets the ERROR_GOOD#_STS bit
— Sets the DONE_STS bit.
Intel
®
ICH7 Family Datasheet
Functional Description
Related parts for NH82801GHM S L8YR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
82801GHM I/O Controller Hub 7 (ICH7MDH)
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Microprocessor: Intel Celeron M Processor 320 and Ultra Low Voltage Intel Celeron M Processor at 600MHz
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 64 Mbit. Access speed 150 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 100 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
DA28F640J5A-1505 Volt Intel StrataFlash Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 6300ESB I/O Controller Hub
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801DB I/O Controller Hub (ICH4), Pb-Free SLI
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801FB I/O Controller Hub (ICH6)
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel Strataflash Memory28F128J3 28F640J3 28F320J3
Manufacturer:
Intel Corporation
Datasheet: