NH82801GHM S L8YR Intel, NH82801GHM S L8YR Datasheet - Page 576
NH82801GHM S L8YR
Manufacturer Part Number
NH82801GHM S L8YR
Description
Manufacturer
Intel
Datasheet
1.NH82801GHM_S_L8YR.pdf
(848 pages)
Specifications of NH82801GHM S L8YR
Lead Free Status / RoHS Status
Compliant
- Current page: 576 of 848
- Download datasheet (7Mb)
576
Bit
6
5
4
3
2
1
0
Force Port Resume — R/W.
0 = No resume (K-state) detected/driven on port. (Default)
1 = Resume detected/driven on port. Software sets this bit to a 1 to drive resume
NOTE: When the EHCI controller owns the port, the resume sequence follows the
Overcurrent Change — R/WC. The functionality of this bit is not dependent upon the
port owner. Software clears this bit by writing a 1 to it.
0 = No change. (Default)
1 = There is a change to Overcurrent Active.
Overcurrent Active — RO.
0 = This port does not have an overcurrent condition. (Default)
1 = This port currently has an overcurrent condition. This bit will automatically
Port Enable/Disable Change — R/WC. For the root hub, this bit gets set to a 1 only
when a port is disabled due to the appropriate conditions existing at the EOF2 point
(See Chapter 11 of the USB Specification for the definition of a port error). This bit is
not set due to the Disabled-to-Enabled transition, nor due to a disconnect. Software
clears this bit by writing a 1 to it.
0 = No change in status. (Default).
1 = Port enabled/disabled status has changed.
Port Enabled/Disabled — R/W. Ports can only be enabled by the host controller as a
part of the reset and enable. Software cannot enable a port by writing a 1 to this bit.
Ports can be disabled by either a fault condition (disconnect event or other fault
condition) or by host software. Note that the bit status does not change until the port
state actually changes. There may be a delay in disabling or enabling a port due to
other host controller and bus events.
0 = Disable
1 = Enable (Default)
Connect Status Change — R/WC. This bit indicates a change has occurred in the
port’s Current Connect Status. Software sets this bit to 0 by writing a 1 to it.
0 = No change (Default).
1 = Change in Current Connect Status. The host controller sets this bit for all changes
Current Connect Status — RO. This value reflects the current state of the port, and
may not correspond directly to the event that caused the Connect Status Change bit
(Bit 1) to be set.
0 = No device is present. (Default)
1 = Device is present on port.
signaling. The Host controller sets this bit to a 1 if a J-to-K transition is detected
while the port is in the Suspend state. When this bit transitions to a 1 because a J-
to-K transition is detected, the Port Change Detect bit (D29:F7:CAPLENGTH + 24h,
bit 2) in the USB2.0_STS register is also set to a 1. If software sets this bit to a 1,
the host controller must not set the Port Change Detect bit.
transition from 1 to 0 when the over current condition is removed. The Intel
automatically disables the port when the overcurrent active bit is 1.
to the port device connect status, even if system software has not cleared an
existing connect status change. For example, the insertion status changes twice
before system software has cleared the changed condition, hub hardware will be
“setting” an already-set bit (i.e., the bit will remain set).
defined sequence documented in the USB Specification, Revision 2.0. The
resume signaling (Full-speed 'K') is driven on the port as long as this bit
remains a 1. Software must appropriately time the Resume and set this bit to a
0 when the appropriate amount of time has elapsed. Writing a 0 (from 1)
causes the port to return to high-speed mode (forcing the bus below the port
into a high-speed idle). This bit will remain a 1 until the port has switched to the
high-speed idle.
Description
EHCI Controller Registers (D29:F7)
Intel
®
ICH7 Family Datasheet
®
ICH7
Related parts for NH82801GHM S L8YR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
82801GHM I/O Controller Hub 7 (ICH7MDH)
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Microprocessor: Intel Celeron M Processor 320 and Ultra Low Voltage Intel Celeron M Processor at 600MHz
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 64 Mbit. Access speed 150 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 100 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
DA28F640J5A-1505 Volt Intel StrataFlash Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 6300ESB I/O Controller Hub
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801DB I/O Controller Hub (ICH4), Pb-Free SLI
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801FB I/O Controller Hub (ICH6)
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel Strataflash Memory28F128J3 28F640J3 28F320J3
Manufacturer:
Intel Corporation
Datasheet: