SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 1160

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Table 46-36. SSC Timings with 3.3V Peripheral Supply (Continued)
Notes:
Table 46-37. SSC Timings with 1.8V Peripheral Supply
Notes:
1160
Symbol
SSC
SSC
SSC
Symbol
SSC
SSC
SSC
SSC
SSC
SSC
SSC
SSC
SSC
SSC
SSC
SSC
SSC
SSC
11
12
13
0
1
2
3
4
5
6
7
8
9
10
11
12
13
(1)
(1)
1. Timings SSC4 and SSC7 depend on the start condition. When STTDLY = 0 (Receive start delay) and START = 4, or 5 or 7
2. For output signals (TF, TD, RF), Min and Max access times are defined. The Min access time is the time between the TK (or
1. Timings SSC4 and SSC7 depend on the start condition. When STTDLY = 0 (Receive start delay) and START = 4, or 5 or 7
2. For output signals (TF, TD, RF), Min and Max access times are defined. The Min access time is the time between the TK (or
SAM9G45
(Receive Start Selection), two Periods of the MCK must be added to timings.
RK) edge and the signal change. The Max access time is the time between the TK edge and the signal stabilization.
46-18
(Receive Start Selection), two Periods of the MCK must be added to timings.
RK) edge and the signal change. The Max access time is the time between the TK edge and the signal stabilization.
46-18
Parameter
TK edge to TF/TD (TK output, TF output)
TK edge to TF/TD (TK input, TF output)
TF setup time before TK edge (TK output)
TF hold time after TK edge (TK output)
TK edge to TF/TD (TK output, TF input)
TF setup time before TK edge (TK input)
TF hold time after TK edge (TK input)
TK edge to TF/TD (TK input, TF input)
RF/RD setup time before RK edge (RK input)
RF/RD hold time after RK edge (RK input)
RK edge to RF (RK input)
RF/RD setup time before RK edge (RK output)
RF/RD hold time after RK edge (RK output)
RK edge to RF (RK output)
Parameter
RF/RD setup time before RK edge (RK output)
RF/RD hold time after RK edge (RK output)
RK edge to RF (RK output)
illustrates Min and Max accesses for SSC0. The same applies to SSC1, SSC4, and SSC7, SSC10 and SSC13.
illustrates Min and Max accesses for SSC0. The same applies to SSC1, SSC4, and SSC7, SSC10 and SSC13.
Transmitter
Receiver
Cond
Cond
-2.8 (+2*t
5.0 (+3*t
18.4 - t
18.6 - t
14.2 - t
t
t
t
CPMCK
CPMCK
CPMCK
t
t
4.8
5.4
CPMCK
CPMCK
Min
0
Min
0
0
0.6
2.4
CPMCK
CPMCK
(2)
(2)
(2)
CPMCK
CPMCK
CPMCK
(2)
(2)
- 5.1
- 5.1
- 3.9
)
)
(1)(2)
(1)(2)
18.3 (+3*t
4.2 (+2*t
18.4
21.5
4.2
5.3
5.2
Max
Max
CPMCK
CPMCK
(2)
(2)
(2)
(2)
(2)
)
)
(1)(2)
6438G–ATARM–19-Apr-11
(1)(2)
Units
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
s
Figure
Figure