SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 158

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

20.2
20.2.1
20.2.2
20.2.2.1
20.2.2.2
158
External Bus Interface (EBI)
SAM9G45
Description
Embedded Characteristics
External Bus Interface
Static Memory Controller
The External Bus Interface (EBI) is designed to ensure the successful data transfer between
several external devices and the embedded Memory Controller of an ARM-based device.
The Static Memory, DDR, SDRAM and ECC Controllers are all featured external Memory Con-
trollers on the EBI. These external Memory Controllers are capable of handling several types of
external memory and peripheral devices, such as SRAM, PROM, EPROM, EEPROM, Flash,
DDR2 and SDRAM. The EBI operates with 1.8V or 3.3V Power Supply (VDDIOM1).
The EBI also supports the CompactFlash and the NAND Flash protocols via integrated circuitry
that greatly reduces the requirements for external components. Furthermore, the EBI handles
data transfers with up to six external devices, each assigned to six address spaces defined by
the embedded Memory Controller. Data transfers are performed through a 16-bit or 32-bit data
bus, an address bus of up to 26 bits, up to six chip select lines (NCS[5:0]) and several control
pins that are generally multiplexed between the different external Memory Controllers.
The SAM9G45 features an External Bus Interface to interface to a wide range of external mem-
ories and to any parallel peripheral.
• Integrates Three External Memory Controllers:
• Additional logic for NAND Flash and CompactFlash
• Optional Full 32-bit External Data Bus
• Up to 26-bit Address Bus (up to 64 MBytes linear per chip select)
• Up to 6 chip selects, Configurable Assignment:
• 8-, 16- or 32-bit Data Bus
• Multiple Access Modes supported
• Multiple device adaptability
• Multiple Wait State Management
– Static Memory Controller
– DDR2/SDRAM Controller
– SLC Nand Flash ECC Controller
– Static Memory Controller on NCS0
– DDR2/SDRAM Controller (SDCS) or Static Memory Controller on NCS1
– Static Memory Controller on NCS2
– Static Memory Controller on NCS3, Optional NAND Flash support
– Static Memory Controller on NCS4 - NCS5, Optional CompactFlash
– Byte Write or Byte Select Lines
– Asynchronous read in Page Mode supported (4- up to 32-byte page size)
– Control signals programmable setup, pulse and hold time for each Memory Bank
– Programmable Wait State Generation
– External Wait Request
M
6438G–ATARM–19-Apr-11
support