SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 181

no-image

SAM9G45

Manufacturer Part Number
SAM9G45
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of SAM9G45

Flash (kbytes)
0 Kbytes
Pin Count
324
Max. Operating Frequency
400 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
160
Ext Interrupts
160
Usb Transceiver
3
Usb Speed
Hi-Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
2
Uart
5
Lin
4
Ssc
2
Ethernet
1
Sd / Emmc
2
Graphic Lcd
Yes
Video Decoder
No
Camera Interface
Yes
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
440
Resistive Touch Screen
Yes
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
64
Self Program Memory
NO
External Bus Interface
2
Dram Memory
DDR2/LPDDR, SDRAM/LPSDR
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
0.9 to 1.1
Fpu
No
Mpu / Mmu
No/Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
20.2.9
6438G–ATARM–19-Apr-11
Programmable I/O Lines Power Supplies and Drive Levels
The power supply pin VDDIOM1 accepts two voltage ranges. This allows the device to reach its
maximum speed either out of 1.8V or 3.3V external memories.
The maximum speed is 133 MHz on the SDCK pin and #SDCK signals loaded with 10 pF. The
load on data/address and control signals are 30 pF for power supply at 1.8V and 50 pF for power
supply at 3.3V. The data lines frequency reaches 133 MHz in DDR2 mode. The other signals
(control and address) do not go over 66 MHz.
The EBI I/Os accept two drive levels, HIGH and LOW. This allows to avoid overshoots and give
the best performance according to the bus load and external memories. Refer to the EBI Chip
Select Assignment Register for more details.
The voltage ranges and the drive level are determined by programming EBI_DRIVE field in the
Chip Configuration registers located in the Matrix User Interface.
At reset the selected default drive level is High.
At reset, the selected voltage defaults to 3.3V typical and power supply pins can accept either
1.8V or 3.3V. The user must make sure to program the EBI voltage range before getting the
device out of its Slow Clock Mode. The user must make sure to program the EBI voltage range
before getting the device out of its Slow Clock Mode.
• Assign the EBI CS4 and/or EBI_CS5 to the CompactFlash Slot 0 and/or Slot 1 by setting the
• The address line A21 is to select Alternate True IDE (A21=1) or True IDE (A21=0) modes.
• A21, CFRNW, CFS0, CFCS1, CFCE1 and CFCE2 signals are multiplexed with PIO lines and
• Configure a PIO line as an output for CFRST and two others as an input for CFIRQ and
• Configure SMC CS4 and/or SMC_CS5 (for Slot 0 or 1) Setup, Pulse, Cycle and Mode
bit EBI_CS4A and/or EBI_CS5A in the EBI Chip Select Assignment Register located in the
bus matrix memory space.
thus the dedicated PIOs must be programmed in peripheral mode in the PIO controller.
CARD DETECT functions respectively.
accordingly to CompactFlash timings and system bus frequency.
SAM9G45
181

Related parts for SAM9G45