SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 797

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

37. USB High Speed Host Port (UHPHS)
37.1
37.2
37.2.1
6438G–ATARM–19-Apr-11
Description
Embedded Characteristics
EHCI
The USB High Speed Host Port (UHPHS) interfaces the USB with the host application. It han-
dles Open HCI protocol (Open Host Controller Interface) as well as Enhanced HCI protocol
(Enhanced Host Controller Interface).
The AT91SAM9G45 features USB communication ports as follows:
USB Host Port A is directly connected to the first UTMI transceiver.
The Host Port B is multiplexed with the USB device High speed and connected to the second
UTMI port. The selection between Host Port B and USB device high speed is controlled by a the
UDPHS enable bit located in the UDPHS_CTRL control register.
Figure 37-1. USB Selection
The USB Host Port controller is fully compliant with the Enhanced HCI specification. The USB
Host Port User Interface (registers description) can be found in the Enhanced HCI Rev 1.0
Specification available on http://www.intel.com/technology/usb/ehcispec.htm. The standard
EHCI USB stack driver can be easily ported to Atmel’s architecture in the same way all existing
class drivers run, without hardware specialization.
• 2 Ports USB Host full speed OHCI and High speed EHCI
• 1 Device High speed
• Compliant with Enhanced HCI Rev 1.0 Specification
• Compliant with Open HCI Rev 1.0 Specification
• Root Hub Integrated with 2 Downstream USB Ports
• Shared Embedded USB Transceivers
– Compliant with USB V2.0 High-speed and Full-speed Specification
– Supports Both High-speed 480Mbps and Full-speed 12 Mbps USB devices
– Compliant with USB V2.0 Full-speed and Low-speed Specification
– Supports Both Low-speed 1.5 Mbps and Full-speed 12 Mbps USB devices
Transceiver
PA
HS
HS EHCI
FS OHCI
DMA
PB
0
Transceiver
HS
USB
DMA
HS
1
EN_UDPHS
SAM9G45
797