SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 929

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

6438G–ATARM–19-Apr-11
If the bit PRES in
the sequences are as follow:
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
• For Trigger Counter at 0:
1. Close the switches on the inputs X
2. Convert Channel X
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
4. Set Trigger Counter to 1.
• For Trigger Counter at 1:
1. Close the switches on the inputs X
2. Convert Channel Y
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
4. Set Trigger Counter to 2.
• For Trigger Counter at 2:
1. Close the switches on the inputs X
2. Convert Channel X
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
4. Set Trigger Counter to 3.
• For Trigger Counter at 3:
1. Close the switches on the inputs X
2. Convert Channel X
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
4. Set Trigger Counter to 4.
• For Trigger Counter at 4:
1. Close the switches on the inputs X
2. Convert Channel Y
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
4. Set Trigger Counter to 5.
sponding TSADCC_CDRx and TSADCC_LCDR.
TSADCC_LCDR if PDCEN is enabled).
sponding TSADCC_CDRx and TSADCC_LCDR.
TSADCC_LCDR if PDCEN is enabled).
sponding TSADCC_CDRx and TSADCC_LCDR.
sponding TSADCC_CDRx and TSADCC_LCDR.
result in TSADCC_CDR0 (and also in TSADCC_LCDR if PDCEN is enabled).
sponding TSADCC_CDRx and TSADCC_LCDR.
from the result and store the subtraction result in TSADCC_CDR1 (and also in
TSADCC_LCDR if PDCEN is enabled).
sponding TSADCC_CDRx and TSADCC_LCDR.
“TSADCC Mode Register”
P
P
P
M
M
, subtract TSADCC_CDR1 from the result and store the subtraction
and store the result in TSADCC_XPDR, subtract TSADCC_CDR1
and store the result in TSADCC_Z1DR (and also in
and store the result in TSADCC_Z2DR (and also in
and store the result in TSADCC_CDR1.
P
P
P
P
P
and Y
and Y
and X
and X
and X
is enabled (measure both position and pressure),
M
M
M
M
M
during the Sample and Hold Time.
during the Sample and Hold Time.
during the Sample and Hold Time.
during the Sample and Hold Time.
during the Sample and Hold Time.
SAM9G45
929