tm1300 NXP Semiconductors, tm1300 Datasheet - Page 30

no-image

tm1300

Manufacturer Part Number
tm1300
Description
Tm-1300 Media Processor
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
tm1300-1.2
Quantity:
380
TM1300 Data Book
1-6
VO_IO2
VO_CLK
AI_OSCLK
AI_SCK
AI_SD
AI_WS
Pin Name
BGA
Ball
H20
B15
A16
C15
B16
J19
Audio In (always acts as receiver, but can be master or slave for A/D timing)
WEAK5
WEAK5
WEAK5
STRG5
STRG3
STRG5
Type
Pad
PRODUCT SPECIFICATION
Mode
OUT
I/O
I/O
I/O
I/O
IN
This pin can function as FS (frame sync) input, FS output or as ENDMSG output.
• If set as FS input, it can be set to respond to positive or negative edge transitions.
• If the Video Out (VO) unit operates in external sync mode and the selected transition
• In message passing mode, this pin acts as ENDMSG output.
The VO unit emits VO_DATA on a positive edge of VO_CLK. VO_CLK can be config-
ured as input (reset default) or output.
• If configured as input: VO_CLK is received from external display clock master cir-
• If configured as output, TM1300 emits a programmable clock frequency. The emitted
If used as output, a board level 27-33 ohm series resistor is recommended to reduce
ringing.
Over-sampling clock. This output can be programmed to emit any frequency up to 40
MHz with a sub-Hertz resolution. It is intended for use as the 256f
pling clock by external A/D subsystem. A board level 27-33 ohm series resistor is rec-
ommended to reduce ringing.
• When the Audio In (AI) unit is programmed as a serial-interface timing slave
• When the AI unit is programmed as the serial-interface timing master, AI_SCK is an
AI_SCK is limited to 22 MHz. The sample rate of valid samples embedded within the
serial stream is variable. If used as output, a board level 27-33 ohm series resistor is
recommended to reduce ringing.
Serial data from external A/D subsystem. Data on this pin is sampled on positive or
negative edges of AI_SCK as determined by the CLOCK_EDGE bit in the AI_SERIAL
register.
• When the AI unit is programmed as the serial-interface timing slave (power-up
• When Audio In is programmed as the serial-interface timing master, AI_WS acts as
AI_WS is the word-select or frame-synchronization signal from/to the external A/D
subsystem.
occurs, the VO unit sends two fields of video data. Note: this works only once after a
reset.
cuitry.
frequency can be set between approx. 4 and 81 MHz with a sub-Hertz resolution.
The clock generated is frequency accurate and has low jitter properties due to a
combination of an on-chip DDS (Direct Digital Synthesizer) and VCO/PLL.
(power-up default), AI_SCK is an input. AI_SCK receives the serial bit clock from
the external A/D subsystem. This clock is treated as fully asynchronous to the
TM1300 main clock.
output. AI_SCK drives the serial clock for the external A/D subsystem. The fre-
quency is a programmable integral divisors of the AI_OSCLK frequency.
default), AI_WS acts as an input. AI_WS is sampled on the same edge as selected
for AI_SD.
an output. It is asserted on the opposite edge of the AI_SD sampling edge.
Description
Philips Semiconductors
s
or 384f
s
over sam-

Related parts for tm1300