ATSAM3U-EK Atmel, ATSAM3U-EK Datasheet - Page 1000

• Manufacturer Part Number: ATSAM3U-EK
• Description: KIT EVAL FOR AT91SAM3U CORTEX
• Manufacturer: Atmel
• Type: MCUr

Specifications of ATSAM3U-EK

• Contents: Board
• Processor To Be Evaluated: SAM3U
• Data Bus Width: 32 bit
• Interface Type: RS-232, USB
• Operating Supply Voltage: 3 V
• Silicon Manufacturer: Atmel
• Core Architecture: ARM
• Core Sub-architecture: Cortex - M3
• Silicon Core Number: SAM3U4E
• Silicon Family Name: SAM3U
• Kit Contents: Board CD Docs
• Rohs Compliant: Yes
• For Use With/related Products: AT91SAM3U
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

• ERR_OVFLW: Overflow Error
This bit is set by hardware when a new too-long packet is received.
Example: If the user programs an endpoint 64 bytes wide and the host sends 128 bytes in an OUT transfer, then the Over-
flow Error bit is set.
This bit is updated at the same time as the BYTE_COUNT field.
This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by UDPHS_EPTCTLDISx (disable endpoint).
• RX_BK_RDY/KILL_BANK: Received OUT Data/KILL Bank
This bit is set by hardware after a new packet has been stored in the endpoint FIFO.
This bit is cleared by the device firmware after reading the OUT data from the endpoint.
For multi-bank endpoints, this bit may remain active even when cleared by the device firmware, this if an other packet has
been received meanwhile.
Hardware assertion of this bit may generate an interrupt if enabled by the UDPHS_EPTCTLx register RX_BK_RDY bit.
This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint) and by UDPHS_EPTCTLDISx (disable endpoint).
Note:
• TX_COMPLT: Transmitted IN Data Complete
This bit is set by hardware after an IN packet has been transmitted for isochronous endpoints and after it has been
accepted (ACK’ed) by the host for Control, Bulk and Interrupt endpoints.
This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint), and by UDPHS_EPTCTLDISx (disable endpoint).
• TX_PK_RDY/ERR_TRANS: TX Packet Ready/Transaction Error
This bit is cleared by hardware, as soon as the packet has been sent for isochronous endpoints, or after the host has
acknowledged the packet for Control, Bulk and Interrupt endpoints.
For Multi-bank endpoints, this bit may remain clear even after software is set if another bank is available to transmit.
Hardware clear of this bit may generate an interrupt if enabled by the UDPHS_EPTCTLx register TX_PK_RDY bit.
This bit is reset by UDPHS_EPTRST register EPT_x (reset endpoint), and by UDPHS_EPTCTLDISx (disable endpoint).
This bit is set by hardware when a transaction error occurs inside one microframe.
If one toggle sequencing problem occurs among the n-transactions (n = 1, 2 or 3) inside a microframe, then this bit is still
set as long as the current bank contains one “bad” n-transaction. (see
Bank/Control Direction” on page
is reset.
1000
1000
– Received OUT Data: (For OUT endpoint or Control endpoint)
– KILL Bank: (For IN endpoint)
– the bank is really cleared or the bank is sent, BUSY_BANK_STA is decremented.
– the bank is not cleared but sent on the IN transfer, TX_COMPLT
– the bank is not cleared because it was empty. The user should wait that this bit is cleared before trying to clear
– TX Packet Ready:
– Transaction Error: (For high bandwidth isochronous OUT endpoints) (Read-Only)
another packet.
“Kill a packet” may be refused if at the same time, an IN token is coming and the current packet is sent on the UDPHS line. In
this case, the TX_COMPLT bit is set. Take notice however, that if at least two banks are ready to be sent, there is no problem to
kill a packet even if an IN token is coming. In fact, in that case, the current bank is sent (IN transfer) and the last bank is killed.
SAM3U Series
SAM3U Series
1002) As soon as the current bank is relative to a new “good” n-transactions, then this bit
“CURRENT_BANK/CONTROL_DIR: Current
6430D–ATARM–25-Mar-11
6430D–ATARM–25-Mar-11