HD6432621 Hitachi, HD6432621 Datasheet - Page 522
HD6432621
Manufacturer Part Number
HD6432621
Description
(HD64F262x Series) 16-Bit Microcomputer
Manufacturer
Hitachi
Datasheet
1.HD6432621.pdf
(1069 pages)
- Current page: 522 of 1069
- Download datasheet (5Mb)
Break Detection and Processing (Asynchronous Mode Only): When framing error (FER)
detection is performed, a break can be detected by reading the RxD pin value directly. In a break,
the input from the RxD pin becomes all 0s, and so the FER flag is set, and the parity error flag
(PER) may also be set.
Note that, since the SCI continues the receive operation after receiving a break, even if the FER
flag is cleared to 0, it will be set to 1 again.
Sending a Break (Asynchronous Mode Only): The TxD pin has a dual function as an I/O port
whose direction (input or output) is determined by DR and DDR. This can be used to send a break.
Between serial transmission initialization and setting of the TE bit to 1, the mark state is replaced
by the value of DR (the pin does not function as the TxD pin until the TE bit is set to 1).
Consequently, DDR and DR for the port corresponding to the TxD pin are first set to 1.
To send a break during serial transmission, first clear DR to 0, then clear the TE bit to 0.
When the TE bit is cleared to 0, the transmitter is initialized regardless of the current transmission
state, the TxD pin becomes an I/O port, and 0 is output from the TxD pin.
Receive Error Flags and Transmit Operations (Clocked Synchronous Mode Only):
Transmission cannot be started when a receive error flag (ORER, PER, or FER) is set to 1, even if
the TDRE flag is cleared to 0. Be sure to clear the receive error flags to 0 before starting
transmission.
Note also that receive error flags cannot be cleared to 0 even if the RE bit is cleared to 0.
Receive Data Sampling Timing and Reception Margin in Asynchronous Mode:
In asynchronous mode, the SCI operates on a basic clock with a frequency of 16 times the transfer
rate.
In reception, the SCI samples the falling edge of the start bit using the basic clock, and performs
internal synchronization. Receive data is latched internally at the rising edge of the 8th pulse of the
basic clock. This is illustrated in figure 13-21.
478
Related parts for HD6432621
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Silicon N-Channel Power MOS FET Module
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
High Speed Power Switching
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
Silicon N-Channel IGBT
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
8MHz V(cc): -0.3 to +7.0V V(in): -0.3 to +0.3V advanced CRT controller (ACRTC)
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-word ? 4-bit High Speed CMOS Static RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
SINGLE CHIP CODEC WITH FILTERS(COMBO)
Manufacturer:
HITACHI
Datasheet: