HD6432621 Hitachi, HD6432621 Datasheet - Page 680
![no-image](/images/manufacturer_photos/0/3/301/hitachi_sml.jpg)
HD6432621
Manufacturer Part Number
HD6432621
Description
(HD64F262x Series) 16-Bit Microcomputer
Manufacturer
Hitachi
Datasheet
1.HD6432621.pdf
(1069 pages)
- Current page: 680 of 1069
- Download datasheet (5Mb)
Notes: *1 Mode pin and FWE pin input must satisfy the mode programming setup time (t
19.6.2
When set to user program mode, the chip can program and erase its flash memory by executing a
user program/erase control program. Therefore, on-board reprogramming of the on-chip flash
memory can be carried out by providing on-board means of FWE control and supply of
programming data, and storing a program/erase control program in part of the program area as
necessary.
To select user program mode, select a mode that enables the on-chip flash memory (mode 6 or 7),
and apply a high level to the FWE pin. In this mode, on-chip supporting modules other than flash
memory operate as they normally would in modes 6 and 7.
The flash memory itself cannot be read while the SWE1 bit is set to 1 to perform programming or
erasing, so the control program that performs programming and erasing should be run in on-chip
RAM or external memory. If the program is to be located in external memory, the instruction for
writing to flash memory, and the following instruction, should be placed in on-chip RAM.
636
The contents of the CPU’s internal general registers are undefined at this time, so these
registers must be initialized immediately after branching to the programming control program.
In particular, since the stack pointer (SP) is used implicitly in subroutine calls, etc., a stack area
must be specified for use by the programming control program.
The initial values of other on-chip registers are not changed.
Boot mode can be entered by making the pin settings shown in table 19-6 and executing a
reset-start.
Boot mode can be cleared by driving the reset pin low, waiting at least 20 states, then setting
the FWE pin and mode pins, and executing reset release*
WDT overflow reset.
Do not change the mode pin input levels in boot mode, and do not drive the FWE pin low
while the boot program is being executed or while flash memory is being programmed or
erased*
If the mode pin input levels are changed (for example, from low to high) during a reset, the
state of ports with multiplexed address functions and bus control output pins (AS, RD, HWR)
will change according to the change in the microcomputer’s operating mode*
Therefore, care must be taken to make pin settings to prevent these pins from becoming output
signal pins during a reset, or to prevent collision with signals outside the microcomputer.
*2 For further information on FWE application and disconnection, see section 19.13,
*3 See Appendix D, Pin States.
User Program Mode
2
states) with respect to the reset release timing.
Flash Memory Programming and Erasing Precautions.
.
1
. Boot mode can also be cleared by a
3
.
MDS
= 4
Related parts for HD6432621
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PM45502C](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
Silicon N-Channel Power MOS FET Module
Manufacturer:
HITACHI
Datasheet:
![PM50502C](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
High Speed Power Switching
Manufacturer:
HITACHI
Datasheet:
![MBN1200D33A](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
Silicon N-Channel IGBT
Manufacturer:
HITACHI
Datasheet:
![MBM200A6](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
![MBM100A6](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
![MBN300F12](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
![HD63484P8](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
8MHz V(cc): -0.3 to +7.0V V(in): -0.3 to +0.3V advanced CRT controller (ACRTC)
Manufacturer:
HITACHI
Datasheet:
![HM53461P-10](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
![HM53461P-12](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
![HM6208HLP-25](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
65,536-word ? 4-bit High Speed CMOS Static RAM
Manufacturer:
HITACHI
Datasheet:
![HD44233P](/images/manufacturer_photos/0/3/301/hitachi_tmb.jpg)
Part Number:
Description:
SINGLE CHIP CODEC WITH FILTERS(COMBO)
Manufacturer:
HITACHI
Datasheet: