MMC2114CFCAG33 Freescale Semiconductor, MMC2114CFCAG33 Datasheet - Page 387

• Manufacturer Part Number: MMC2114CFCAG33
• Description: IC MCU 32BIT 33MHZ 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCorer

Specifications of MMC2114CFCAG33

• Core Processor: M210
• Core Size: 32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 67
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: MMC2114
• Core: M-CORE
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 33 MHz
• Number Of Programmable I/os: 104
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Controller Family/series: MCORE
• No. Of I/o's: 104
• Ram Memory Size: 32KB
• Cpu Speed: 33MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

17.12.4 Framing Errors
17.12.5 Baud Rate Tolerance
MMC2114 • MMC2113 • MMC2112 — Rev. 1.0
MOTOROLA
RT CLOCK COUNT
RESET RT CLOCK
RT CLOCK
SAMPLES
RXD
1
1
1
Serial Communications Interface Modules (SCI1 and SCI2)
In
RT9, and RT10 high. This sets the noise flag but does not reset the RT
clock. In start bits only, the RT8, RT9, and RT10 data samples are
ignored.
If the data recovery logic does not detect a 1 where the stop bit should
be in an incoming frame, it sets the FE flag in SCISR1. A break frame
also sets the FE flag because a break frame has no stop bit. The FE flag
is set at the same time that the RDRF flag is set.
A transmitting device may be operating at a baud rate below or above
the receiver baud rate. Accumulated bit time misalignment can cause
one of the RT8, RT9, and RT10 stop bit data samples to fall outside the
stop bit. A noise error occurs if the samples are not all the same value.
If more than one of the samples is outside the stop bit, a framing error
occurs. In most applications, the baud rate tolerance is much more than
the degree of misalignment that is likely to occur.
As the receiver samples an incoming frame, it resynchronizes the RT
clock on any valid falling edge within the frame. Resynchronization
within frames corrects misalignments between transmitter bit times and
receiver bit times.
1
Figure 17-22. Start Bit Search Example 6
Figure 17-22
Freescale Semiconductor, Inc.
1
For More Information On This Product,
1
1
Go to: www.freescale.com
1
1
a noise burst makes the majority of data samples RT8,
0
Serial Communications Interface Modules (SCI1 and SCI2)
0
0
START BIT
0
1
0
1
Advance Information
LSB
Receiver
387