MMC2114CFCAG33 Freescale Semiconductor, MMC2114CFCAG33 Datasheet - Page 617

• Manufacturer Part Number: MMC2114CFCAG33
• Description: IC MCU 32BIT 33MHZ 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCorer

Specifications of MMC2114CFCAG33

• Core Processor: M210
• Core Size: 32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 67
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: MMC2114
• Core: M-CORE
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 33 MHz
• Number Of Programmable I/os: 104
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Controller Family/series: MCORE
• No. Of I/o's: 104
• Ram Memory Size: 32KB
• Cpu Speed: 33MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MMC2114 • MMC2113 • MMC2112 — Rev. 1.0
MOTOROLA
Operating supply current, crystal/PLL clocking
RAM memory standby supply current
FLASH memory supply current
Analog supply current
ESD supply current
DC injection current
1. Refer to
2. Current measured at maximum system clock frequency (unless indicated otherwise), all modules active, and default drive
3. Current measured at f
4. All functional non-supply pins are internally clamped to V
5. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
6. Power supply must maintain regulation within operating V
Master mode
Single-chip mode
Wait mode
Doze mode
Stop mode
Normal operation: V
Transient condition: V
Standby operation: V
Read
Program
Erase or mass erase
Stop mode
Normal operation
Stop mode
Normal operation
Stop mode
V
Single pin limit
Total MCU limit, includes sum of all stressed pins
NEGCLAMP
OSC and PLL enabled
OSC enabled, PLL disabled
OSC and PLL disabled
strength with matching load.
with matching load.
resistance values for positive and negative clamp voltages, then use the larger of the two values.
conditions. If positive injection current (V
result in external power supply going out of regulation. Ensure external V
injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is
present, or if clock rate is very low which would reduce overall power consumption. Also, at power-up, system clock is not
present during the power-up sequence until the PLL has attained lock.
Table 23-5
= V
SS
– 0.3 V, V
(4), (5), (6)
through
DD
Table 23-4. DC Electrical Specifications
DD
SYS
STBY
> V
< V
= 32 MHz derived from 8.00 MHz crystal and PLL, all modules active, and default drive strength
Parameter
STBY
–0.3 V > V
Table 23-10
SS
POSCLAMP
(4)
(V
Freescale Semiconductor, Inc.
+ 0.5 V
– 0.3 V
SS
For More Information On This Product,
= V
Preliminary Electrical Specifications
DD
in
= V
for additional PLL, QADC and FLASH specifications.
> V
SSF
> V
Go to: www.freescale.com
DD
DD
SS
(3)
) is greater than I
= V
+ 0.3
+ 0.5 V
SSA
SS
DD
= 0 V, T
and their respective V
range during instantaneous and operating maximum current
DD
, the injection current may flow out of V
A
Symbol
I
= T
DDXTAL
I
DD
I
I
I
STBY
DDA
DDH
DDF
I
IC
load will shunt current greater than maximum
L
(1)
to T
(Continued)
DD
Preliminary Electrical Specifications
.
H
)
–1.0
Min
–10
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
DC Electrical Specifications
Advance Information
Max
10.0
200
800
1.0
64
44
19
14
10
20
28
20
10
10
2
1
7
5
1
2
DD
and could
Unit
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
A
A
A
A
A
A
617