R5F213J6CNNP#U0 Renesas Electronics America, R5F213J6CNNP#U0 Datasheet - Page 658

• Manufacturer Part Number: R5F213J6CNNP#U0
• Description: MCU 1KB FLASH 32K ROM 36-QFN
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/3JCr

Specifications of R5F213J6CNNP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 31
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 36-WQFN Exposed Pad, 36-HWQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/3JC Group
REJ09B0602-0100 Rev.1.00
May 12, 2010
Figure 31.7
31.4.10 Data Protect Function
(Lock bit disable select bit)
(Ready/busy status flag)
Each block in the flash memory has a nonvolatile lock bit. The lock bit is enabled by setting the FMR13 bit in
the FMR1 register is set to 0 (lock bit enabled). The lock bit can be used to disable (lock) programming or
erasing each block. This prevents data from being written or erased inadvertently. A block status changes
according to the lock bit as follows:
•
•
The lock bit data is set to 0 (locked) by executing the lock bit program command and to 1 (not locked) by
erasing the block. No commands can be used to set only the lock bit data to 1.
The lock bit data can be read using the read lock bit status command.
When the FMR13 bit is set to 1 (lock bit disabled), the lock bit function is disabled and all blocks are not locked
(each lock bit data remains unchanged). The lock bit function is enabled by setting the FMR13 bit to 0 (the lock
bit data is retained).
When the block erase command is executed while the FMR13 bit is set to 1, the target block is erased regardless
of the lock bit status. The lock bit of the erase target block is set to 1 after auto-erasure completes.
Refer to 31.4.11 Software Commands for the details of individual commands.
The FMR13 bit is set to 0 after auto-erasure completes. This bit is also set to 0 if one of the following conditions
is met. To erase or program a different locked block, set the FMR 13 bit to 1 again and execute the block erase
or program command.
•
•
•
•
•
Figure 31.7 shows the FMR13 Bit Operation Timing.
When the lock bit data is set to 0: locked (the block cannot be programmed or erased)
When the lock bit data is set to 1: not locked (the block can be programmed and erased)
If the FST7 bit in the FST register is changed from 0 (busy) to 1 (ready).
If a command sequence error occurs.
If the FMR01 bit in the FMR0 register is set to 0 (CPU mode disabled).
If the FMSTP bit in the FM0 register is set to 1 (flash memory stops).
If the CMDRST bit in the FMR0 register is set to 1 (erasure/writing stopped).
FMR13 bit
Operation
FMR13 Bit Operation Timing
FST7 bit
Set to 1 by a program.
Erase start
Erase
Lock bit enabled
Erase completion
0 is set at the rising edge of the FST7 bit.
FST7: Bit in FST register
FMR13: Bit in FMR1 register
31. Flash Memory
Page 627 of 715