NH82801FBM S L89K Intel, NH82801FBM S L89K Datasheet - Page 484
NH82801FBM S L89K
Manufacturer Part Number
NH82801FBM S L89K
Description
Manufacturer
Intel
Datasheet
1.NH82801FBM_S_L89K.pdf
(786 pages)
Specifications of NH82801FBM S L89K
Lead Free Status / RoHS Status
Compliant
- Current page: 484 of 786
- Download datasheet (5Mb)
SATA Controller Registers (D31:F2)
12.2.1
484
BMIC[P,S]—Bus Master IDE Command Register
Address Offset:
Default Value:
Bit
7:4
2:1
3
0
Reserved. Returns 0.
Read / Write Control (RWC) — R/W. This bit sets the direction of the bus master transfer: This bit
must NOT be changed when the bus master function is active.
0 = Memory reads
1 = Memory writes
Reserved. Returns 0.
Start/Stop Bus Master (START) — R/W.
0 = All state information is lost when this bit is cleared. Master mode operation cannot be stopped
1 = Enables bus master operation of the controller. Bus master operation does not actually start
NOTE: This bit is intended to be cleared by software after the data transfer is completed, as
and then resumed. If this bit is reset while bus master operation is still active (i.e., the Bus
Master IDE Active bit (D31:F2:BAR + 02h, bit 0) of the Bus Master IDE Status register for that
IDE channel is set) and the drive has not yet finished its data transfer (the Interrupt bit in the
Bus Master IDE Status register for that IDE channel is not set), the bus master command is said
to be aborted and data transferred from the drive may be discarded instead of being written to
system memory.
unless the Bus Master Enable bit (D31:F1:04h, bit 2) in PCI configuration space is also set. Bus
master operation begins when this bit is detected changing from 0 to 1. The controller will
transfer data between the IDE device and memory only when this bit is set. Master operation
can be halted by writing a 0 to this bit.
indicated by either the Bus Master IDE Active bit being cleared or the Interrupt bit of the Bus
Master IDE Status register for that IDE channel being set, or both. Hardware does not clear
this bit automatically. If this bit is cleared to 0 prior to the DMA data transfer being initiated
by the drive in a device to memory data transfer, then the ICH6 will not send DMAT to
terminate the data transfer. SW intervention (e.g. sending SRST) is required to reset the
interface in this condition.
Primary: BAR + 00h
Secondary: BAR + 08h
00h
Intel
Description
®
I/O Controller Hub 6 (ICH6) Family Datasheet
Attribute:
Size:
R/W
8 bits
(D31:F2)
Related parts for NH82801FBM S L89K
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Intel
Datasheet:
Part Number:
Description:
Microprocessor: Intel Celeron M Processor 320 and Ultra Low Voltage Intel Celeron M Processor at 600MHz
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 64 Mbit. Access speed 150 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 100 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
DA28F640J5A-1505 Volt Intel StrataFlash Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 6300ESB I/O Controller Hub
Manufacturer:
Intel Corporation
Datasheet: