TMPM361F10FG Toshiba, TMPM361F10FG Datasheet - Page 584

• Manufacturer Part Number: TMPM361F10FG
• Manufacturer: Toshiba

Specifications of TMPM361F10FG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Contact Us
• Rom (kbytes): 1024K
• Rom Type: Flash
• Ram (kbytes): 64K
• Number Of Pins: 100
• Package: LQFP(14Ã?14)
• Vcc: 3V
• Cpu Mhz: 64
• Ssp (ch) Spi: 1
• I2c/sio (ch): 3
• Uart/sio (ch): 5
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: 8
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 16
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: Y
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit

20.4
Description of Operations
20.4.4
20.4.5
20.4.5.1
ized to "0000".
low.
After a reset, ADMOD0<REPEAT,SCAN> is initialized to "00" and ADMOD1<ADCH[3:0]> is initial-
The channels to be converted are selected according to the operation mode of the AD converter as shown be-
activated by setting ADMOD2<HPADCE> to "1".
sion, one of these operation modes must be selected by setting ADMOD0<REPEAT,SCAN> to an appropri-
ate setting. For top-priority AD conversion, only one operation mode can be used: fixed channel single con-
version mode.
MOD4<ADHS>, and top-priority AD conversion can be activated using the HW activation source selec-
ted by ADMOD4<HADHS>. If bits of <ADHS> and <HADHS> are "0", normal and top-priority AD con-
versions are activated in response to the input of a falling edge through the ADTRG pin. If these bits are
"1", normal AD conversion is activated in response to TB6RG0 generated by the 16-bit timer 6, and top-pri-
ority AD conversion is activated in response to TB5RG0 generated by the 16-bit timer 5.
MOD4<HADHTG> to "1" for top-priority AD conversion.
Selecting the Input Channel
AD Conversion Details
1. Normal AD conversion mode
2. Top-priority AD conversion mode
Note 1: When an external trigger is used for the HW activation source of a top-priority AD conversion, an external trig-
Note 2: TMPM361F10FG disables the external trigger used for H/W activation. Therefore "0" cannot be set to
Normal AD conversion is activated by setting ADMOD0<ADS> to "1". Top-priority AD conversion is
Four operation modes are made available to normal AD conversion. In performing normal AD conver-
Normal AD conversion can be activated using the H/W activation source selected by AD-
To permit H/W activation, set ADMOD4<ADHTG> to "1" for normal AD conversion and set AD-
Software activation is still valid even after H/W activation has been permitted.
Starting AD Conversion
MOD2<HPADCH> to an appropriate setting.
・ If the analog input channel is used in a fixed state (ADMOD0<SCAN> = "0")
・ If the analog input channel is used in a scan state (ADMOD0<SCAN> = "1")
One channel is selected from analog input pins from AIN0 through AIN7 by setting AD-
ger cannot be set for activating normal AD conversion H/W.
<HADHS> and <ADHS>.
MOD1<ADCH> to an appropriate setting.
ADSCN to an appropriate setting.
One channel is selected from analog input pins AIN0 through AIN7 by setting AD-
One scan mode is selected from the scan modes by setting ADMOD1 <ADCH> and
Page 560
TMPM361F10FG