TMPM361F10FG Toshiba, TMPM361F10FG Datasheet - Page 633

• Manufacturer Part Number: TMPM361F10FG
• Manufacturer: Toshiba

Specifications of TMPM361F10FG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Contact Us
• Rom (kbytes): 1024K
• Rom Type: Flash
• Ram (kbytes): 64K
• Number Of Pins: 100
• Package: LQFP(14Ã?14)
• Vcc: 3V
• Cpu Mhz: 64
• Ssp (ch) Spi: 1
• I2c/sio (ch): 3
• Uart/sio (ch): 5
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: 8
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 16
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: Y
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit

22.2.10
Note:
gram offers these four commands, of which the details are provided on the following subsections.
If a password is set to 0xFF (erased data), it is difficult to protect data securely due to an easy-to-
guess password. Even if Single Boot mode is not used, it is recommended to set a unique value as a
password.
When Single Boot mode is selected, the boot program is automatically executed on startup. The boot pro-
Operation of Boot Program
1. RAM Transfer command
2. Show Flash Memory SUM command
3. Show Product Information command
4. Flash Memory Chip Erase and Protection Bit Erase command
chip RAM and executes the program once the transfer is successfully completed. The user program
RAM space can be assigned to the range from 0x2000_0400 to the end address of RAM, whereas
the boot program area (0x2000_0000 to 0x2000_03FF) is unavailable. The user program starts at
the assigned RAM address.
own; this provides the ability to control on-board programming of the flash memory in a unique man-
ner. The programming routine must utilize the flash memory command sequences described in Sec-
tion 22.3. Before initiating a transfer, the RAM Transfer command verifies a password sequence com-
ing from the controller against that stored in the flash memory.
The boot program does not provide a command to read out the contents of the flash memory. In-
stead, the Flash Memory SUM command can be used for software revision management.
tion and the like. This command also reads out the contents of the flash memory locations at address-
es shown below. In addition to the Show Flash Memory Sum command, these locations can be
used for software revision management.
ory cell and their protection conditions are erased even when any of the blocks are prohibited from
writing and erasing. When the command is completed, the FCSECBIT <SECBIT> bit is set to "1".
This command serves to recover boot programming operation when a user forgets the password.
Therefore password verification is not executed.
The RAM Transfer command stores program code transferred from the host controller to the on-
The RAM Transfer command can be used to download a flash programming routine of your
The Show Flash Memory SUM command adds the entire contents of the flash memory together.
The Show Product Information command provides the product name, on-chip memory configura-
This command erases the entire area of the flash memory automatically. All the blocks in the mem-
TMPM361F10FG
Product name
Page 609
0x3F8F_FFF0 to 0x3F8F_FFF3
Area
TMPM361F10FG