DF2148BTE20 Renesas Electronics America, DF2148BTE20 Datasheet - Page 18

IC H8S MCU FLASH 128K 100-QFP

DF2148BTE20

Manufacturer Part Number
DF2148BTE20
Description
IC H8S MCU FLASH 128K 100-QFP
Manufacturer
Renesas Electronics America
Series
H8® H8S/2100r
Datasheets

Specifications of DF2148BTE20

Core Processor
H8S/2000
Core Size
16-Bit
Speed
20MHz
Connectivity
I²C, IrDA, SCI, X-Bus
Peripherals
PWM, WDT
Number Of I /o
74
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 8x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 75°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Other names
HD64F2148BTE20
HD64F2148BTE20

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DF2148BTE20V
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Rev. 3.00 Mar 21, 2006 page xvi of liv
Item
23.8.1 Program/
Program-Verify
Figure 23.11
Program/Program-
Verify Flowchart
Section 24 Clock
Pulse Generator
Figure 24.1 Block
Diagram of Clock
Pulse Generator
24.5 Subclock Input
Circuit
25.1.1 Standby
Control Register
(SBYCR)
Page
625
633
639
643
Revision (See Manual for Details)
Figure 23.11 amended
Notes: 1. Data transfer is performed by byte transfer. The lower 8 bits of the first address written
Section of “Masked ROM” deleted
Figure 24.1 amended
(Before) 2 to f32
Description of “When Subclock Is Not Needed” and “Note on
Subclock Usage” added
Table amended
… SCK2 to SCK0 must be cleared to B'000.
2. Verify data is read in 16-bit (word) units.
3. Even bits for which programming has been completed will be subjected to programming once again if the result of the subsequent verify operation is NG.
4. A 128-byte area for storing program data, a 128-byte area for storing reprogram data, and a 128-byte area for storing additional data must be provided in RAM.
5. A write pulse of z1 s or z2 s is applied according to the progress of the programming operation. See note 7 for details of the pulse widths. When writing of
6. The values of x, y, z1, z2, z3, α, β, γ, ε, η, θ, and N are shown in sections 28.1.6 and 28.2.6, Flash Memory Characteristics.
Reprogram Data Computation Table
Original Data
to must be H'00 or H'80. A 128-byte data transfer must be performed even if writing
fewer than 128 bytes; in this case, H'FF data must be written to the extra addresses.
The contents of the reprogram data area and additional data area are modified as programming proceeds.
additional-programming data is executed, a z3 s write pulse should be applied. Reprogram data X' means reprogram data when the write pulse is applied.
(D)
0
0
1
1
Note: 7. Write Pulse Width
Note: Use a z3 s write pulse for additional programming.
Number of Writes n
Verify Data
Write pulse application subroutine
(V)
Wait (z1) s, (z2) s or (z3) s
1000
0
1
0
1
998
999
10
11
12
13
Clear PSU bit in FLMCR2
Reprogram data storage
Additional-programming
1
2
3
4
5
6
7
8
9
Sub-Routine Write Pulse
Set PSU bit in FLMCR2
Program data storage
Clear P bit in FLMCR1
Set P bit in FLMCR1
data storage area
area (128 bytes)
area (128 bytes)
(128 bytes)
Reprogram Data
WDT enable
Disable WDT
Wait (α) s
Wait (β) s
Wait (γ) s
RAM
End Sub
(X)
1
0
1
1
Write Time (z) s
z1
z1
z1
z1
z1
z1
z2
z2
z2
z2
z2
z2
z2
z2
z2
z2
Programming completed
Programming incomplete; reprogram
Still in erased state; no action
*
6
*
*
*
*
6
5
6
6
Comments
*
6
(After) 2 to 32
Increment address
Additional-Programming Data Computation Table
Successively write 128-byte data from additional-
Apply write pulse (Additional programming) z3 s
programming data area in RAM to flash memory
Reprogram
NG
Data (X')
Transfer reprogram data to reprogram data area
Additional-programming data computation
Transfer additional-programming data to
Store 128-byte program data in program
0
0
1
1
data area consecutively to flash memory
Write 128-byte data in RAM reprogram
H'FF dummy write to verify address
data area and reprogram data area
additional-programming data area
Apply
Clear SWE bit in FLMCR1
Reprogram data computation
data verification completed?
Set SWE bit in FLMCR1
Clear PV bit in FLMCR1
Set PV bit in FLMCR1
Start of programming
Verify Data
write pulse z1
End of programming
Read verify data
Wait (x) s
Write data =
OK
Wait (η) s
OK
Wait (θ) s
(V)
Wait (γ) s
Wait (ε) s
verify data?
0
1
0
1
OK
START
128-byte
m = 0 ?
m = 0
6 n ?
n = 1
6 n?
OK
OK
Sub-Routine-Call
Programming Data (Y)
s or z2 s
Additional-
NG
NG
NG
0
1
1
1
*
NG
*
*
*
See note 7 for pulse width
*
*
*
*
*
*
6
6
4
1
6
6
6
3
6
2
*
*
4
4
*
*
m = 1
1
3
Perform programming in the erased state.
Do not perform additional programming
on previously programmed addresses.
Additional programming to be executed
Additional programming not to be executed
Additional programming not to be executed
*
6
Clear SWE bit in FLMCR1
Programming failure
Wait (θ) s
n
(N)?
Comments
OK
NG
n
n + 1
*
6

Related parts for DF2148BTE20