DF2148BTE20 Renesas Electronics America, DF2148BTE20 Datasheet - Page 437

IC H8S MCU FLASH 128K 100-QFP

DF2148BTE20

Manufacturer Part Number
DF2148BTE20
Description
IC H8S MCU FLASH 128K 100-QFP
Manufacturer
Renesas Electronics America
Series
H8® H8S/2100r
Datasheets

Specifications of DF2148BTE20

Core Processor
H8S/2000
Core Size
16-Bit
Speed
20MHz
Connectivity
I²C, IrDA, SCI, X-Bus
Peripherals
PWM, WDT
Number Of I /o
74
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 8x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 75°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Other names
HD64F2148BTE20
HD64F2148BTE20

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DF2148BTE20V
Manufacturer:
Renesas Electronics America
Quantity:
10 000
15.4.5
Figure 15.6 shows an example of the operation for transmission in asynchronous mode. In
transmission, the SCI operates as described below.
1. The SCI monitors the TDRE flag in SSR, and if it is cleared to 0, recognizes that data has been
2. After transferring data from TDR to TSR, the SCI sets the TDRE flag to 1 and starts
3. Data is sent from the TxD pin in the following order: start bit, transmit data, parity bit or
4. The SCI checks the TDRE flag at the timing for sending the stop bit.
5. If the TDRE flag is 0, the data is transferred from TDR to TSR, the stop bit is sent, and then
6. If the TDRE flag is 1, the TEND flag in SSR is set to 1, the stop bit is sent, and then the “mark
Figure 15.7 shows a sample flowchart for transmission in asynchronous mode.
Figure 15.6 Example of SCI Transmit Operation in Asynchronous Mode (Example with 8-
written to TDR, and transfers the data from TDR to TSR.
transmission. If the TIE bit in SCR is set to 1 at this time, a transmit data empty interrupt
request (TXI) is generated. Because the TXI interrupt routine writes the next transmit data to
TDR before transmission of the current transmit data has finished, continuous transmission can
be enabled.
multiprocessor bit (may be omitted depending on the format), and stop bit.
serial transmission of the next frame is started.
state” is entered in which 1 is output. If the TEIE bit in SCR is set to 1 at this time, a TEI
interrupt request is generated.
TXI interrupt
request generated
TDRE
TEND
Data Transmission (Asynchronous Mode)
1
Start
bit
0
Data written to TDR and
TDRE flag cleared to 0 in
TXI interrupt handling routine
D0
D1
1 frame
Data
Bit Data, Parity, One Stop Bit)
D7
Parity
bit
Section 15 Serial Communication Interface (SCI and IrDA)
0/1
TXI interrupt
request generated
Stop
bit
1
Start
bit
0
D0
Rev. 3.00 Mar 21, 2006 page 381 of 788
D1
Data
D7
Parity
bit
TEI interrupt
request generated
0/1
Stop
bit
REJ09B0300-0300
1
Idle state
(mark state)
1

Related parts for DF2148BTE20