TMP92xy21FG Toshiba, TMP92xy21FG Datasheet - Page 230

• Manufacturer Part Number: TMP92xy21FG
• Manufacturer: Toshiba

Specifications of TMP92xy21FG

• Package: LQFP144
• Rom Types(m=mask,p=otp, F=flash,e=eeprom): Romless
• Rom Combinations: Romless
• Ram Combinations: 16
• Architecture: 32-bit CISC
• Usb/spi Channels: -
• Uart/sio Channels: 2
• I2c/sio Bus Channels: -
• (s)dram Controller: 1
• Adc 10-bit Channel: 4
• Da Converter: -
• Timer 8-bit Channel: 4
• Timer 16-bit Channel: 1
• Pwm 8-bit Channels: -
• Pwm 16-bit Channels: -
• Cs/wait Controller: 4
• Dual Clock: Y
• Number Of I/o Ports: 82
• Power Supply Voltage(v): 3.0 to 3.6

EP1_MODE
EP2_MODE
EP3_MODE
(0789H)
(078AH)
(078BH)
3.10.3.24 EPx_MODE Register (x: 1 to 3)
bit Symbol
Read/Write
Reset State
bit Symbol
Read/Write
Reset State
bit Symbol
Read/Write
Reset State
Note1: When writing to this register, a recovery time of 5clocks at 12MHz is needed. After writing this register, insert
Note2: When writing to this register, endpoint is initialized same as RESET of COMMAND register.
Note3: Max packet size of Isochronous transfer type is 1023 bytes.
Note4: IfwMaxPacketSize of descriptor was set to other than 8, 16, ..., 1023, Payload more than descriptor value is
dummy instruction of 420 ns or longer.
set by auto-answer of Set_Configration and Set_Interface.
control must use appointed config or interface. Access this register to set mode.
INT_SETUP interrupt is received, finish writing before accessing EOP register. This
register prohibits writing when it is timing, and it is ignored.
This register sets transfer mode of endpoint (EP1 to EP3).
If SET_CONFIG and SET_INTERFACE processing is set to software control, this
There is a limitation to the timing that can be written.
If SET_CONFIG and SET_INTERFACE processing is set to software control, after
DIRECTION (Bit0)
MODE [1:0] (Bit1 and bit2)
PAYLOAD [2:0] (Bit3, bit4 and bit5)
Others (Bit6 and bit7) Reserved
7
7
7
0: OUT
1: IN
00: Control transfer type
01: Isochronous transfer type
10: Bulk transfer type or interrupt transfer type
11: Interrupt (No toggle)
Note: If setting endpoint that is set to Isochronous transfer mode to “no use”, after changing to
000:
001:
010:
011:
0100:128 bytes
0101:256 bytes
0110:512 bytes
0111:1023 bytes (Note1, 2)
Isochronous mode, set to “no use” by COMMAND register.
16 bytes
32 bytes
64 bytes
8 bytes
6
6
6
Direction from host to device
Direction from device to host
Payload[2]
Payload[2]
Payload[2]
92CH21-228
R/W
R/W
R/W
5
5
5
0
0
0
Payload[1]
Payload[1]
Payload[1]
R/W
R/W
R/W
4
4
4
0
0
0
Payload[0]
Payload[0]
Payload[0]
R/W
R/W
R/W
3
3
3
0
0
0
Mode[1]
Mode[1]
Mode[1]
R/W
R/W
R/W
2
2
2
0
0
0
Mode[0]
Mode[0]
Mode[0]
R/W
R/W
R/W
1
1
1
0
0
0
TMP92CH21
2009-06-19
Direction
Direction
Direction
R/W
R/W
R/W
0
0
0
0
0
0