UPD70F3771GF-GAT-AX Renesas Electronics America, UPD70F3771GF-GAT-AX Datasheet - Page 221

• Manufacturer Part Number: UPD70F3771GF-GAT-AX
• Description: MCU 32BIT V850ES/JX3-H 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Hr

Specifications of UPD70F3771GF-GAT-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 48MHz
• Connectivity: CAN, CSI, EBI/EMI, I²C, UART/USART, USB
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 2.85 V ~ 3.6 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

V850ES/JG3-H, V850ES/JH3-H
R01UH0042EJ0400 Rev.4.00
Sep 30, 2010
(3) TAAn I/O control register 0 (TAAnIOC0)
The TAAnIOC0 register is an 8-bit register that controls the timer output (TOAAn0, TOAAn1 pins).
This register can be read or written in 8-bit or 1-bit units.
Reset sets this register to 00H.
(n = 0 to 3, 5)
TAAnIOC0
After reset: 00H
Note The output level of the timer output pin (TOAAnm) specified by the
Cautions 1. Rewrite the TAAnOL1, TAAnOE1, TAAnOL0, and TAAnOE0
Remark
TAAnOL1
TAAnOE1
TAAnOE0
TAAnOL0
• When TAAnOLm bit = 0
0
1
0
1
0
1
0
1
7
0
TOAAnm pin output
TAAnOLm bit is shown below.
2. Even if the TAAnOLm bit is manipulated when the TAAnCE
m = 0, 1
Timer output disabled
• When TAAnOL1 bit = 0: Low level is output from the TOAAn1 pin
• When TAAnOL1 bit = 1: High level is output from the TOAAn1 pin
Timer output disabled
• When TAAnOL0 bit = 0: Low level is output from the TOAAn0 pin
• When TAAnOL0 bit = 1: High level is output from the TOAAn0 pin
TOAAn1 pin output starts at high level
TOAAn1 pin output starts at low level
TOAAn0 pin output starts at high level
TOAAn0 pin output starts at low level
Timer output enabled (a square wave is output from the TOAAn1 pin).
Timer output enabled (a square wave is output from the TOAAn0 pin).
R/W
16-bit counter
TAAnCE bit
bits when the TAAnCTL0.TAAnCE bit = 0. (The same value
can be written when the TAAnCE bit = 1.) If rewriting was
mistakenly performed, clear the TAAnCE bit to 0 and then
set the bits again.
and TAAnOEm bits are 0, the TOAAnm pin output level
varies.
6
0
Address: TAA0IOC0 FFFFF632H, TAA1IOC0 FFFFF642H,
CHAPTER 7 16-BIT TIMER/EVENT COUNTER AA (TAA)
5
0
TOAAn1 pin output level setting
TOAAn0 pin output level setting
TAA2IOC0 FFFFF652H, TAA3IOC0 FFFFF662H,
TAA5IOC0 FFFFF682H
TOAAn1 pin output setting
TOAAn0 pin output setting
4
0
TAAnOL1 TAAnOE1 TAAnOL0 TAAnOE0
• When TAAnOLm bit = 1
TOAAnm pin output
3
16-bit counter
TAAnCE bit
2
Note
Note
1
0
Page 221 of 1509