TMPM330FWFG Toshiba, TMPM330FWFG Datasheet - Page 329

• Manufacturer Part Number: TMPM330FWFG
• Description: Microcontrollers (MCU) MCU w/ ARM Cortex-M3 128K FLASH, 8K SRAM
• Manufacturer: Toshiba

Specifications of TMPM330FWFG

• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 128K
• Rom Type: Flash
• Ram (kbytes): 8K
• Number Of Pins: 100
• Package: LQFP(14×14)
• Vcc: 3V
• Cpu Mhz: 40
• Ssp (ch) Spi: -
• I2c/sio (ch): 3
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: -
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: 12
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 10
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit
• Lead Free Status / Rohs Status: Details

14.2.9
<RMCDATH6:0>:
<RMCDATL6:0>:
(Note)
Remote Control Receive Control Register 3 [RMCRCR3]
Read/Write
Read/Write
bit Symbol
After reset
bit Symbol
After reset
Function
Function
If the <RMCPHM> bit of the Remote Control Receive Control Register 2 is “0”,
<RMCDATH6:0> are not enabled. The bits are enabled when <RMCPHM> is ”1”.
Specifies a larger threshold (within a range of 1.5T and 2T) to determine a pattern
of remote control signal in a phase method. If the measured cycle exceeds the
threshold, the bit is determined as “10”. If not, the bit is determined as “01”.
Calculating formula of the threshold: RMCDATHx1/fs[s].
Specifies two kinds of thresholds: a threshold to determine whether a data bit is 0
or 1; a smaller threshold (within a range of 1T and 1.5T) to determine a pattern of
remote control signal in a phase method.
As for the determination of data bit, if the measured cycle exceeds the threshold,
the bit is determined as “1”. If not, the bit is determined as “0”. Calculating formula
of the threshold: RMCDATL×1/fs[s].
As for the determination of a remote control signal pattern in a phase method, if the
measured cycle exceeds the threshold, the bit is determined as “01”. If not, the bit
is determined as “00”. Calculating formula of the threshold to determine 0 or 1:
RMCDATLx1/fs[s].
”0” is
read.
”0” is
read.
15
―
―
R
7
R
0
0
Larger threshold to determine a signal pattern in a phase method
RMCDATH×1/fs[s]
Threshold to determine 0 or 1/
smaller threshold to determine a signal pattern in a phase method
RMCDATL×1/fs[s]
RMCDAT
RMCDAT
Under development
14
H6
L6
6
RMCDAT
RMCDAT
Page317
13
H5
L5
5
RMCDAT
RMCDAT
12
H4
L4
4
RMCDAT
RMCDAT
11
H3
L3
W
W
3
0
0
RMCDAT
RMCDAT
10
H2
L2
2
RMCDAT
RMCDAT
H1
L1
9
1
TMPM330
RMCDAT
RMCDAT
H0
L0
8
0